AutoCAD 2010/2011/2012

Reply
Valued Contributor
Spiritshifterus
Posts: 97
Registered: ‎07-30-2012
Message 1 of 8 (441 Views)
Accepted Solution

Punched-out region question

441 Views, 7 Replies
01-10-2013 08:21 AM

Good morning, all.

 

I've never tried this in AutoCAD before, so that is why I've come to the experts here for help. I would like to create a simple rectangular area with a circle in its center. When this area is hatched, the circle is hollowed out. Furthermore, I'd like to have this to insert into a block for stretch action manipulation. Is this possible with AutoCAD 2010?

 

Thank you all.

 

Chris Martin

Hi,

 

>> I feel that you misunderstand what I am asking about.

if so then sorry, but I give it an additional try.

If that is also wrong, then at least it helps that you can then describe what you don't like here.

 

- alfred -

*Expert Elite*
Alfred.NESWADBA
Posts: 9,207
Registered: ‎06-29-2007
Message 2 of 8 (435 Views)

Re: Punched-out region question

01-10-2013 09:05 AM in reply to: Spiritshifterus

Hi,

 

should be possible, haven't you tried it?

 

- alfred -

-------------------------------------------------------------------------
Alfred NESWADBA
Ingenieur Studio HOLLAUS ... www.hollaus.at
-------------------------------------------------------------------------
Valued Contributor
Spiritshifterus
Posts: 97
Registered: ‎07-30-2012
Message 3 of 8 (433 Views)

Re: Punched-out region question

01-10-2013 09:11 AM in reply to: Alfred.NESWADBA

I have tried the Region command, but only for a few moments. And each time I tried, the command created two regions (the rectangle, and the circle). These remained separate to themselves; I could not figure out how to combine them, especially since the two elements do not intersect at any point.

 

Thank you.

 

Chris Martin

*Expert Elite*
Alfred.NESWADBA
Posts: 9,207
Registered: ‎06-29-2007
Message 4 of 8 (428 Views)

Re: Punched-out region question

01-10-2013 09:19 AM in reply to: Spiritshifterus

Hi,

 

>> I have tried the Region command

Don't use region, use command _RECTANG for rectangle as polyline, then draw a circle and last but not least create the hatch.

 

- alfred -

-------------------------------------------------------------------------
Alfred NESWADBA
Ingenieur Studio HOLLAUS ... www.hollaus.at
-------------------------------------------------------------------------
Valued Contributor
Spiritshifterus
Posts: 97
Registered: ‎07-30-2012
Message 5 of 8 (425 Views)

Re: Punched-out region question

01-10-2013 09:26 AM in reply to: Alfred.NESWADBA

Pardon me, sir, but I feel that you misunderstand what I am asking about.

 

I need to display a solidly filled rectangle area, and if the rectangle was a piece of paper, the circle would be a punched-out hole in its center. Wipeouts can do this, but only for linear polylines (no arcs). That is why I am asking about regions.

 

Chris Martin

*Expert Elite*
Alfred.NESWADBA
Posts: 9,207
Registered: ‎06-29-2007
Message 6 of 8 (415 Views)

Re: Punched-out region question

01-10-2013 10:05 AM in reply to: Spiritshifterus

Hi,

 

>> I feel that you misunderstand what I am asking about.

if so then sorry, but I give it an additional try.

If that is also wrong, then at least it helps that you can then describe what you don't like here.

 

- alfred -

-------------------------------------------------------------------------
Alfred NESWADBA
Ingenieur Studio HOLLAUS ... www.hollaus.at
-------------------------------------------------------------------------
New Member
sancdub
Posts: 1
Registered: ‎01-10-2013
Message 7 of 8 (406 Views)

Re: Punched-out region question

01-10-2013 11:09 AM in reply to: Spiritshifterus

That is your idea?

Valued Contributor
Spiritshifterus
Posts: 97
Registered: ‎07-30-2012
Message 8 of 8 (381 Views)

Re: Punched-out region question

01-11-2013 07:40 AM in reply to: Alfred.NESWADBA

Dear Mr. Neswadba,

 

I took a look at your file. Thank you for it. I managed to get close to what you had before I began this thread. It appeared that I was not properly grabbing points & handling parameters when I dealt with the hatching. I have now accepted your thread as the solution, and you have my thanks.

 

Chris Martin

 

(A note to User sancdub: you were also on the same track as Mr. Neswadba and I. Thank you for your input also.)

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.