Revit MEP

Reply
Active Member
comtois.william
Posts: 7
Registered: ‎04-05-2012
Message 1 of 13 (686 Views)

Which family template should I use to create supports or hangers for pipes?

686 Views, 12 Replies
09-24-2012 07:19 AM

Hi everyone,

 

I'm new with Revit and I need to create a family of supports or hangers.

 

Which template should I use if I want to place my supports on my pipes and then adjust the parameters to make it fit on steel beams?

 

I tried to use Plumbing Fixtures, but when I inserted it in my project, i couldn't place them the way I wanted.

 

Regards,

William Comtois

 

P.S. : I found a topic on the subject, but it didn't really help me out - http://forums.autodesk.com/t5/Autodesk-Revit-MEP/Query-for-pipe-supports-or-hangers-in-Revit-Mep/m-p...

Active Contributor
tjbeecher
Posts: 43
Registered: ‎06-18-2007
Message 2 of 13 (679 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:03 AM in reply to: comtois.william

We have used pipe accessories and that seem to work well.

 

Active Member
comtois.william
Posts: 7
Registered: ‎04-05-2012
Message 3 of 13 (674 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:16 AM in reply to: tjbeecher

tjbeecher wrote:

We have used pipe accessories and that seem to work well.

 



Am I supose to find this .RFT in the basic templates of Revit MEP?

Otherwise, can you send it to me please? :smileyhappy:

 

Regards,

William Comtois

Active Contributor
tjbeecher
Posts: 43
Registered: ‎06-18-2007
Message 4 of 13 (672 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:18 AM in reply to: comtois.william

I am using 2013.  I had to create it with a generic model template then change it before I started modeling the hangers.

Active Member
comtois.william
Posts: 7
Registered: ‎04-05-2012
Message 5 of 13 (667 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:35 AM in reply to: tjbeecher

Ok, I am using 2013 too, but when you say that you had to change it before you started modeling the hangers, what did you change?

Active Contributor
tjbeecher
Posts: 43
Registered: ‎06-18-2007
Message 6 of 13 (664 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:38 AM in reply to: comtois.william

Attached are to pictures. one is showing the family categories and paramteres buttonto click on.  Once the box comes up scroll down to the pipe accessoeris one.

Active Member
comtois.william
Posts: 7
Registered: ‎04-05-2012
Message 7 of 13 (658 Views)

Re: Which family template should I use to create supports or hangers for pipes?

09-24-2012 08:59 AM in reply to: tjbeecher

Well, and do I need to change any parameters or just change the categorie to "pipe accessories"?

 

I tried to just change the categorie, i modeled something simple (A cylinder) and I tried to insert it in my project. Nothing happened... My cylinder seems not to be added in my project...

 

Some ideas?

 

Regards,

William Comtois

Active Contributor
CADArmor
Posts: 32
Registered: ‎10-20-2011
Message 8 of 13 (576 Views)

Re: Which family template should I use to create supports or hangers for pipes?

10-02-2012 11:49 PM in reply to: comtois.william

Hi you need to be using a Generic Model Template found in (C:\ProgramData\Autodesk\RME 2011\Metric Templates)

Make sure to add Pipe Connectors one in and one out. (See image attached)

For family Category & Parameters make you’re to Part Type is set at Breaks Into (See image attached)

Active Member
comtois.william
Posts: 7
Registered: ‎04-05-2012
Message 9 of 13 (543 Views)

Re: Which family template should I use to create supports or hangers for pipes?

10-04-2012 10:50 AM in reply to: CADArmor

Thanks for your answer,

 

I tried to create a simple cylinder and to put it down on my piping system the way you told me to do it, but when i do so, some transitions appear on both sides of my cylinder (see image attached)

 

Is there anything to do to avoid those transitions?

 

Thanks,

Will

Active Contributor
CADArmor
Posts: 32
Registered: ‎10-20-2011
Message 10 of 13 (511 Views)

Re: Which family template should I use to create supports or hangers for pipes?

10-04-2012 05:55 PM in reply to: comtois.william

Hi mate

You need to make sure that your radius on your pipe connector is the same size as the pipe in your model. See image attached.

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Revit Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Revit helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Revit

Twitter

Facebook

Blogs

Youtube