Revit Architecture

Reply
Distinguished Contributor
ChuckEdwards
Posts: 113
Registered: ‎04-13-2010
Message 1 of 7 (1,222 Views)
Accepted Solution

Curtain wall louvre panel?

1222 Views, 6 Replies
12-13-2013 10:57 AM

I'm trying to work up a standard curtain wall type for our office, and have hit a snag with a curtain wall panel.

 

I'm trying to make a panel which will feature a louvre profile, that will sit in the curtain wall opening nice and neat, and array the required height of the panel.

 

I've made up a generic object, inserted that into a CW panel, then got that into my CW OK, and it flexs fine, but if I try and do an array then it all falls apart?

 

As far as I've got attached, all I can get to work properly is to have the top and bottom louvre, if I turn this into an array it extends outside the bounds of the CW panels left/right reference plans.

 

I also have tried to do the array based on a division, e.g. 2000/50 = array number, but to do this I need a height, and when I try and put a height in it becomes overconstrained...again, any suggestions?

*Expert Elite*
Alfredo_Medina
Posts: 2,814
Registered: ‎06-11-2009
Message 2 of 7 (1,198 Views)

Re: Curtain wall louvre panel?

12-14-2013 03:35 AM in reply to: ChuckEdwards

There is a "quick" way, and an "advanced" way to do this. It all depends on the time available and your level of skills in making families.

 

The "quick" way is this:

 

Make a new curtain mullion profile with the shape of the blind of the louver. Load this profile into project, and create a new mullion type with this profile. Then, in a curtain wall, create new grid lines by segment, inside the panel where you want the louver to be. Then, create mullions at those new grid lines, using your new "louver" kind of mullion. Then, select all the glass panels that were created in between each louver mullion and change them to "empty".

 

The "advanced" way is this:

 

Make a profile family with the shape of the blind of the louver. Load this profile into a generic model family and create a sweep, controlled by a length parameter. Start a new family with the Curtain Wall Panel template. Create reference planes from the front view, to define the location of the first and last blind of the louver. Create a parameter for spacing, and use that to control the distance of these reference planes in relation to the top and bottom of the panel. Load the generic model family, and place it at one of the horizontal reference planes of the front view. Create an instance reporting parameter to measure the width of the panel. Associate the nested sweep's length parameter to the width of the panel. Array the sweep vertically. Constrain the array to the top reference plane. Create a reporting parameter to get the height of the panel. Use that reporting parameter to determine the number of items of the array. Load into project, and assing this panel to a curtain wall panel. The curtain wall panel must be not driven by type as the one you are using now, which does not let you to define panels types for individual panels.

 

-----------------------------------------------------------------------------------------------------------------
Planta1 Revit Online Consulting | info@planta1.com | my Twitter | The Planta1 Blog
Distinguished Contributor
ChuckEdwards
Posts: 113
Registered: ‎04-13-2010
Message 3 of 7 (1,190 Views)

Re: Curtain wall louvre panel?

12-14-2013 07:46 AM in reply to: ChuckEdwards

Alfredo, your second solution is so obvious I didn't think of it!

 

Thanks, I'll do that instead, much simpler.

*Expert Elite*
Alfredo_Medina
Posts: 2,814
Registered: ‎06-11-2009
Message 4 of 7 (1,175 Views)

Re: Curtain wall louvre panel?

12-14-2013 01:56 PM in reply to: ChuckEdwards

The advanced solution is simpler than the quick solution?

 

-----------------------------------------------------------------------------------------------------------------
Planta1 Revit Online Consulting | info@planta1.com | my Twitter | The Planta1 Blog
Distinguished Contributor
ChuckEdwards
Posts: 113
Registered: ‎04-13-2010
Message 5 of 7 (1,140 Views)

Re: Curtain wall louvre panel?

12-15-2013 02:04 PM in reply to: Alfredo_Medina

Alfredo,

 

I say the second is simpler as it requires rather less onerous manipulation by the end user, most of whom will struggle with something like this.

 

Worked up revision attached.

 

I've added a low detail version of my louvre so it makes it look simpler for elevations where we don't want to see a lot of lines, early stage planning drawings perhaps. I've also set the constraints so the louvres can be variable size apart, with the louvres themselves adjusting in size too. Spacing comes out nice and even as you'd expect. Louvres overlap as also would be expected, which also minimises visible linework.

 

Comments?

*Expert Elite*
Alfredo_Medina
Posts: 2,814
Registered: ‎06-11-2009
Message 6 of 7 (1,072 Views)

Re: Curtain wall louvre panel?

12-22-2013 10:25 AM in reply to: ChuckEdwards

Hi,

I made a quick test, changing the width and height of the panel, and your louver panel works very well. Thanks for sharing.

 

-----------------------------------------------------------------------------------------------------------------
Planta1 Revit Online Consulting | info@planta1.com | my Twitter | The Planta1 Blog
Distinguished Contributor
ChuckEdwards
Posts: 113
Registered: ‎04-13-2010
Message 7 of 7 (1,052 Views)

Re: Curtain wall louvre panel?

12-23-2013 02:32 AM in reply to: Alfredo_Medina

Alfredo,

 

Thanks right back at you, its a virtuous circle.

 

Update to my CW type attached, I made an adjustment so there are now two panel types, one a complex louvre shape, the other a simple shape more appropriate for low level detail work, whihc one you see is controlled by a tick box in the Type. I also added an allowance for varying the spacing.

 

Regards,

 

Charles.

 

(PS can you believe I'm yet to sue Revit on a project yet? We're not allowed...)

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Revit Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Revit helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Revit

Twitter

Facebook

Blogs

Youtube