QuickCAD
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
*Bunnell, Will C.
Symbol rotation
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
19 Views, 2 Replies
02-27-2000 06:32 PM
Hello --
I created two window symbols, placed them in the Architecture
symbol file. When I extract either of them to a drawing, they are
rotated 45 degrees to the left. Any idea what happened when I
created these things?
Thanks
Will
I created two window symbols, placed them in the Architecture
symbol file. When I extract either of them to a drawing, they are
rotated 45 degrees to the left. Any idea what happened when I
created these things?
Thanks
Will
*Norris, Ric
Re: Symbol rotation
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-27-2000 11:30 PM in reply to:
*Bunnell, Will C.
Hi Will,
This may or may not be the answer you are looking for......but have you
checked to make sure that the angle set on the edit bar is at 0 when you
insert your symbols...???
Ric Norris.
"Will C. Bunnell" wrote in message
news:38B9DE47.25BD7E9C@harborside.com...
> Hello --
> I created two window symbols, placed them in the Architecture
> symbol file. When I extract either of them to a drawing, they are
> rotated 45 degrees to the left. Any idea what happened when I
> created these things?
> Thanks
> Will
>
This may or may not be the answer you are looking for......but have you
checked to make sure that the angle set on the edit bar is at 0 when you
insert your symbols...???
Ric Norris.
"Will C. Bunnell"
news:38B9DE47.25BD7E9C@harborside.com...
> Hello --
> I created two window symbols, placed them in the Architecture
> symbol file. When I extract either of them to a drawing, they are
> rotated 45 degrees to the left. Any idea what happened when I
> created these things?
> Thanks
> Will
>
*Bunnell, Will C.
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-28-2000 11:31 AM in reply to:
*Bunnell, Will C.
Hello Ric --
What was in the edit bar when those symbols were created went into the "bit
bucket" some time ago. However, a couple of tests I just ran indicate your
idea of what happened is probably right. Thanks!
Will
Ric Norris wrote:
> Hi Will,
>
> This may or may not be the answer you are looking for......but have you
> checked to make sure that the angle set on the edit bar is at 0 when you
> insert your symbols...???
>
> Ric Norris.
>
> "Will C. Bunnell" wrote in message
> news:38B9DE47.25BD7E9C@harborside.com...
> > Hello --
> > I created two window symbols, placed them in the Architecture
> > symbol file. When I extract either of them to a drawing, they are
> > rotated 45 degrees to the left. Any idea what happened when I
> > created these things?
> > Thanks
> > Will
> >
What was in the edit bar when those symbols were created went into the "bit
bucket" some time ago. However, a couple of tests I just ran indicate your
idea of what happened is probably right. Thanks!
Will
Ric Norris wrote:
> Hi Will,
>
> This may or may not be the answer you are looking for......but have you
> checked to make sure that the angle set on the edit bar is at 0 when you
> insert your symbols...???
>
> Ric Norris.
>
> "Will C. Bunnell"
> news:38B9DE47.25BD7E9C@harborside.com...
> > Hello --
> > I created two window symbols, placed them in the Architecture
> > symbol file. When I extract either of them to a drawing, they are
> > rotated 45 degrees to the left. Any idea what happened when I
> > created these things?
> > Thanks
> > Will
> >
