Inventor General

Reply
Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 1 of 11 (422 Views)
Accepted Solution

sheet metal

422 Views, 10 Replies
11-15-2012 04:33 AM

I make this part in sheet metal.I do not do much with sheet metal tools but have i constructed this part correctly.Could i please have some feedback as the part is correct in shape but i am not sure if it is done correctly construction wise

Thanks

Simon

*Expert Elite*
Posts: 25,352
Registered: ‎04-20-2006
Message 2 of 11 (400 Views)

Re: sheet metal

11-15-2012 09:27 AM in reply to: simon_toaldo

How will that be manufactured?

(looks to me like it should be an assembly of at least 3 parts.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2014 Edu 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 3 of 11 (357 Views)

Re: sheet metal

11-16-2012 04:34 AM in reply to: JDMather

Thanks

Yes 3 pieces.The top and bottom cut to shape and the centre piece bent to shape and all 3 put together.How would you create these 3 pieces in sheet metal and then assemble.Could you if possible show your solution.

Appreciated

Simon

Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 4 of 11 (322 Views)

Re: sheet metal

11-17-2012 04:27 AM in reply to: simon_toaldo

I had a look at the part today on  a fitting and it looks like it is 1 piece.Does this seem possible.It looks like it was 1 piece and then folded to shape.This is a learning exercise for me so any help appreciated

 

Simon

*Expert Elite*
Posts: 25,352
Registered: ‎04-20-2006
Message 5 of 11 (319 Views)

Re: sheet metal

11-17-2012 05:39 AM in reply to: simon_toaldo

simon_toaldo wrote:

I had a look at the part today on  a fitting and it looks like it is 1 piece.Does this seem possible.It looks like it was 1 piece and then folded to shape.This is a learning exercise for me so any help appreciated

 

Simon


It must have some seams (Rips) that were welded together or it is a deep drawn deformed part.
If it has welded seams - indicate where those are.
If it is deep drawn - that is not a folding manufacturing process and Inventor will not develop the blank.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2014 Edu 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 6 of 11 (312 Views)

Re: sheet metal

11-17-2012 05:57 AM in reply to: JDMather

please see attached picture.There is 3 pieces.The weld will be along the 2 edges of piece 2.How can this be done in assembly please

 

simon

Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 7 of 11 (290 Views)

Re: sheet metal

11-18-2012 03:16 AM in reply to: simon_toaldo

I`m interested to see how this would be made in assembly.Could someone with much more experience them me show me how they would do this.

Regards

Simon

Valued Mentor
Posts: 457
Registered: ‎08-02-2003
Message 8 of 11 (253 Views)

Re: sheet metal

11-18-2012 11:55 PM in reply to: simon_toaldo

Hi Simon,

Something like the attached should give you an idea.

Best Regards,

Igor.

Web: www.meqc.com.au
Valued Contributor
Posts: 73
Registered: ‎04-19-2012
Message 9 of 11 (246 Views)

Re: sheet metal

11-19-2012 01:11 AM in reply to: simon_toaldo

Hi Igor

 

Thanks for the model.Appreciated

 

Would the next step be to weld the edges?

 

Regards

 

Simon

Valued Mentor
Posts: 457
Registered: ‎08-02-2003
Message 10 of 11 (198 Views)

Re: sheet metal

11-19-2012 04:46 PM in reply to: simon_toaldo

Hi Simon,

Yes, it would. But not in Inventor. In real life instead. I could never fully understand why would it be necessary to actually show the welds on the model. What's wrong with just indicating the welds on the drawing, as in good old days?

Regards,

Igor.

Web: www.meqc.com.au

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you interested in helping shape the Autodesk Community?
We’re looking at a few different ways to improve the “All Forums” landing page and need your feedback! If interested, please take a few minutes to fill out the following Usability Study. Thank you for your time!

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube