Inventor General

Reply
*Expert Elite*
blair
Posts: 3,943
Registered: ‎11-13-2006
Message 11 of 20 (243 Views)

Re: shape

12-12-2012 08:51 AM in reply to: tborland

Leave it with me for a while, I think that this might have to be converted to a surface model and patches done to get the blend and then back to a solid.

 

I tried some delete face and heal, but it's hung up my system.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 12 of 20 (223 Views)

Re: shape

12-13-2012 03:56 AM in reply to: blair

Greetings Blair

 

I would truly appreciate the model when you do get a chance.Surfaces is 1 tool i would like to learn

 

Best Regards

 

Tony

Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 13 of 20 (206 Views)

Re: shape

12-17-2012 03:19 AM in reply to: blair

Hi

 

I attempted to create this shape with surfaces.Having not done before this is as far as i can go at this point...is this how you are going to create the shape with surfaces?

 

It would be nice to get this hape correct.

 

Thanks again

Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 14 of 20 (187 Views)

Re: shape

12-18-2012 05:16 AM in reply to: blair

Hi Blair

 

Just a quick question

 

1. Was the attached surface model how you would make the model?

 

2. Will you be able to post your attempt anytime soon

 

Thank you

*Expert Elite*
blair
Posts: 3,943
Registered: ‎11-13-2006
Message 15 of 20 (174 Views)

Re: shape

12-18-2012 08:23 AM in reply to: blair

I haven't even had time to look at doing anything on this (some of us work 6 days a week and do this to fill in the remainder of the time).

 

You should be starting to coil the other way. You will still have a problem with the transition of the "Feed Tube" into the body. Either this needs to have a pitch (increasing in radius) or the center of the "Feed-Tube" can't be at the same point as the center of the body.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 16 of 20 (156 Views)

Re: shape

12-19-2012 04:32 AM in reply to: blair

Hi Blair

 

Yes i appreciate any help you offer.....you guys are generous in devoting your time with help.....i will just keep checking back just in case you may find some time.If not i understand you are too busy

 

Best Regards

 

TB

Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 17 of 20 (140 Views)

Re: shape

12-20-2012 06:00 AM in reply to: tborland

Here is the section i am having trouble creating....is this for surfaces to get the correct appearance?

 

Thanks

Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 18 of 20 (126 Views)

Re: shape

12-21-2012 05:29 AM in reply to: blair

I made a little further progress.I would sure like some help with this.If i can get the throat section correct the rest i can finish..I am not familiar with surfaces but i have tried to use for this section but ubfortunately do not know how to get it to look like the picture attach..

Can someone help with this section so as to create like in the picture

 

Thanks alot

 

Tony

Valued Contributor
tborland
Posts: 63
Registered: ‎10-17-2009
Message 19 of 20 (113 Views)

Re: shape

12-21-2012 02:37 PM in reply to: blair

Is there any reason why i cannot get any help on this part (surface part - picture included)...maybe i should just forget asking

 

I understand and appreciate any help but i see other post getting help which are no more dificult then this request...if it is not possible to achieve i would rather someone say and i will stop asking

 

Merry christmas to you all

 

Tony

*Expert Elite*
blair
Posts: 3,943
Registered: ‎11-13-2006
Message 20 of 20 (97 Views)

Re: shape

12-22-2012 08:07 PM in reply to: tborland

1.) When people post with files "created with educational version", people are reluctant to do the students work. This shows the tube with the proper transistion/blend into the body.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube