Inventor General

Reply
Distinguished Contributor
Mark.Downes
Posts: 108
Registered: ‎11-18-2010
Message 1 of 5 (199 Views)
Accepted Solution

rotate origin issue 2014

199 Views, 4 Replies
01-23-2014 05:05 AM

Hi all,

 

I am having an intermittent issue with panning the view around a part or an assembly.

When I click “Shift & Middle Mouse Button” rotate sometimes the part will rotate around the Screen Triad Origin and the same part at a different time will rotate around the part origin.

 

When the part rotates around the Triad origin I can press the “Space bar” and it goes back to rotating around the part origin.

This is a new thing that has only started since I updated to 2014. Does anyone else have this issue?

 

Thanks

Mark

Inventor 2014 64-bit

SP1 Build 222

 

Rotate origin.JPG

Distinguished Mentor
rdyson
Posts: 876
Registered: ‎04-11-2005
Message 2 of 5 (180 Views)

Re: rotate origin issue 2014

01-23-2014 06:43 AM in reply to: Mark.Downes
Hold F4 and click where you want the center of rotation to be. It needs to inside or near the circle, so it may take a couple of clicks.
Better still, buy a 3-D controller.
Distinguished Contributor
Mark.Downes
Posts: 108
Registered: ‎11-18-2010
Message 3 of 5 (165 Views)

Re: rotate origin issue 2014

01-23-2014 07:33 AM in reply to: rdyson

Hi rdyson,

 

Thanks for the reply, since upgrading inventor to 2014 I seem to be getting quite a few things going wrong (or acting different). I have just had another crash for no apparent reason.

 

Hopefully in the next week or so (because I keep whinging at my boss) I should be getting the graphics card updated to a GTX 780. As a side note, I have also upgraded a plugin called MDTools 750 for manifold design. This might also be a cause for the rotation origin changing – Oh hum!)

 

Thanks

Mark

Product Support
pierre.masson
Posts: 227
Registered: ‎05-27-2010
Message 4 of 5 (122 Views)

Re: rotate origin issue 2014

01-27-2014 12:23 AM in reply to: Mark.Downes

Mark,

 


As Rdyson mentioned, using F4 is more practical.

If you want to rotate around one specific component : zoom on it so it's in the center of the view, F4 and click in the center of the view, then with F4 you'll rotate around this.

Pierre Masson Product Support Specialist PS MFG EMEA Autodesk, Inc.
Distinguished Contributor
Mark.Downes
Posts: 108
Registered: ‎11-18-2010
Message 5 of 5 (111 Views)

Re: rotate origin issue 2014

01-27-2014 02:23 AM in reply to: pierre.masson

Hi Pierre,

 

Thanks for the follow up reply. Rotating using "Shift - middle mouse" was never an issue using Inventor 2010, 2012 and 2013.

Maybe its just an Idiosyncrasy of my particular setup (old pc,  graphic drivers etc...)

 

Hey - on the bright side, I might even be able to get my boss to fund a new pc (ha)

 

Cheers

Mark

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube