Inventor General

Reply
Distinguished Contributor
Posts: 406
Registered: ‎11-24-2003
Message 1 of 5 (31 Views)

constraint question

31 Views, 4 Replies
12-10-2002 12:13 AM
I am drawing an assembly of a spring loaded ball plunger.
When I insert the ball into the housing, what type of constraint should I use to ensure the ball protrudes .048"
from the housing.
*Dotson, Sean
Message 2 of 5 (31 Views)

Re: constraint question

12-10-2002 12:20 AM in reply to: koehler
You'll need to use some workplanes on the ball and
the socket.  Then use mate-mate on the ball and socket's workplanes. 
(You can even get fancy then make them adaptive to have the ball retract when
necessary <g>)


--
Sean Dotson, PE

href="http://www.sdotson.com">http://www.sdotson.com

Check the Inventor
FAQ for most common questions

href="http://www.sdotson.com/faq.html">http://www.sdotson.com/faq.html

-----------------------------------------


style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
I
am drawing an assembly of a spring loaded ball plunger.
When I insert the
ball into the housing, what type of constraint should I use to ensure the ball
protrudes .048"
from the housing.
Distinguished Contributor
Posts: 406
Registered: ‎11-24-2003
Message 3 of 5 (31 Views)

Re:

12-10-2002 02:36 AM in reply to: koehler
OK. Got it. One more constraint question:
How do I constain 4 slotted holes to 4 shafts and centered on the slotted hole?
Thanks Bill
*Dotson, Sean
Message 4 of 5 (31 Views)

Re:

12-10-2002 02:44 AM in reply to: koehler
Make two workplanes bisecting each slot in each
direction.  Now put a axis through the planes (it's now perp to your
surface).  Now mate-mate the axis to the shafts.


--
Sean Dotson, PE

href="http://www.sdotson.com">http://www.sdotson.com

Check the Inventor
FAQ for most common questions

href="http://www.sdotson.com/faq.html">http://www.sdotson.com/faq.html

-----------------------------------------


style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
OK.
Got it. One more constraint question:
How do I constain 4 slotted holes to
4 shafts and centered on the slotted hole?
Thanks
Bill
Distinguished Contributor
Posts: 2,068
Registered: ‎12-10-2003
Message 5 of 5 (31 Views)

Re:

12-10-2002 02:55 AM in reply to: koehler
When I draw the slot I usually have some type of point in the center of the sketch I extruded. A workpoint or the end of a construction line. After I extrude the slot I turn the sketch visibility on and create a work axis by selecting the sketch plane and then my center of the slot (the 2D sketch point). I then turn the sketch visibility off. - Rich Thomas

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube