Inventor General

Reply
Member
altoroos
Posts: 4
Registered: ‎02-16-2013
Message 1 of 5 (467 Views)
Accepted Solution

Wind pressure simulation. Help needed.

467 Views, 4 Replies
02-16-2013 05:01 AM

Greetings

I need help and advice on choosing the correct software to do a project I am working on for my Civil Engineering degree at the University of Pretoria in South Africa.

My project is about Fog Harvesting Nets. I must simulate and determine the wind pressures on different types of nets as well as the whole structure of the fog harvesting nets. I must be able to change the wind speed as well as the density of the wind plus the permeability and weight of the nets.

Can you please point me to the right software as well as where I will be able to learn the basics of the software so that I can make a success of this project.

Regards

Alto Roos

Contributor
PiotrekL1
Posts: 19
Registered: ‎01-03-2013
Message 2 of 5 (437 Views)

Re: Wind pressure simulation. Help needed.

02-16-2013 09:32 AM in reply to: altoroos

Hi

 

I am trying to build VAWT( Vertical Axis Wind Turbine) H-Darrieus type for my engineer's project . I found Autodesk Simulation CFD. Good as for students it's free as well as Inventor.  The problem is that I've never used it before and it looks complicated:-( I must do airfoils and whole structure in Inventor first.

 

Cheers

Member
altoroos
Posts: 4
Registered: ‎02-16-2013
Message 3 of 5 (418 Views)

Re: Wind pressure simulation. Help needed.

02-17-2013 01:19 AM in reply to: PiotrekL1
Thanks for the information. I will check the program out and hopefully I will be able to make sense of it. But will still like to be more certain that Simulation CFD will get the job done before I start spending long periods of time on it. I'ts fine by me if I have to build it first in Inventor. Thanks again.
*Expert Elite*
Inv_kaos
Posts: 728
Registered: ‎07-26-2007
Message 4 of 5 (386 Views)

Re: Wind pressure simulation. Help needed.

02-18-2013 02:15 AM in reply to: altoroos

This would do what you need. It will be much easier to learn than CFX, FLUENT, STAR-CCM+, etc plus you get it free as a student. If you can't do it with that software then it would be too advanced for an undergraduate program anyway.

 

There are some videos on the SimSquad website:

www.autodesk.com/simsquad

 

And ask any questions in the Simulation CFD forum:

http://forums.autodesk.com/t5/Autodesk-Simulation-CFD/bd-p/330

 

Please mark as "Accept as Solution" if it answers your question or "Kudos" if you found it useful.
---------------------------------------------------------------------------------------------------------------------
Stew, AICP
Inventor Professional 2013, Autodesk Simulation Multiphysics 2013
Windows 7 x64 Core i7 32GB Ram FX2000
Member
altoroos
Posts: 4
Registered: ‎02-16-2013
Message 5 of 5 (362 Views)

Re: Wind pressure simulation. Help needed.

02-18-2013 07:26 AM in reply to: Inv_kaos

Thanks for the advice. Much appreciated.  Will take this route then.

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube