Inventor General

Reply
Contributor
conbuc
Posts: 25
Registered: ‎02-28-2011
Message 1 of 4 (505 Views)

Will iPart or iAssembly do this?

505 Views, 3 Replies
09-18-2012 02:45 PM

A lot of layouts I work on utilize tube style augers (screw conveyors).

 

The general gist of the screw conveyor is once you lock down the inlet and outlet the rest falls into place and a spec sheet can be generated to send off to the vendor.

 

I would like to create a detailed screw conveyor assembly model (call it a master model) that can be copied, given a unique number and assembled into a layout. I then would like to constrain both ends (inlet/outlet) of the screw conveyor and have it shrink or grow to fit.

 

This would be the preferred method as opposed to typing in variables to generate the screw THEN place it in the assembly. I would rather have the assembly drive the variables of the screw.

 

Can someone give me ideas of how this can be accomplished? Would iPart or iAssembly work for this? Any tutorials or links would be great too!

 

I have attached an image showing the basic specs I need to order a screw conveyor.

 

Thank you.

*Expert Elite*
Posts: 25,259
Registered: ‎04-20-2006
Message 2 of 4 (498 Views)

Re: Will iPart or iAssembly do this?

09-18-2012 03:16 PM in reply to: conbuc

I think I would use Multi-body solids with iLogic and then only push out to assembly if needed.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2014 Edu 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Product Support
AndrewSears
Posts: 249
Registered: ‎08-21-2010
Message 3 of 4 (424 Views)

Re: Will iPart or iAssembly do this?

10-04-2012 03:20 PM in reply to: conbuc

Hey Conrad,

 

Did JD's solution get you in the right direction?  The iLogic portion will give you the conditional variations you need for the part file and then the multi-solid body (MSB) workflow would give you the assembly followed by the spec sheet (drawing) creation.  

 

If you are using Vault, you could use copy design to speed up the process after the first spec sheet is completed.

 

Andy

Contributor
conbuc
Posts: 25
Registered: ‎02-28-2011
Message 4 of 4 (420 Views)

Re: Will iPart or iAssembly do this?

10-04-2012 03:23 PM in reply to: AndrewSears

Hello Andrew,

 

At first glance I was confused by JD's reply and really haven't had a chance lately to work with it. However between his reply and your reply I believe I should be able to figure it out. I hope to get back to that "side project" next week. I will be sure to post back what I find.

 

Thanks for your help.

 

Regards

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube