Inventor General

Reply
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 1 of 12 (494 Views)
Accepted Solution

Tapered Coil

494 Views, 11 Replies
11-05-2012 04:34 AM

Heyy there, 

 

Im using Inventor 2013 and im trying to make a tapered coil but instead of creating it with a liner taper i want a curved taper. Is there a way to create this (prehaps using guide curves like loft feature?) 

 

Im new to inventor but have been using solidworks for a while any help would be appreciated. 

*Expert Elite*
Cadmanto
Posts: 3,175
Registered: ‎12-07-2011
Message 2 of 12 (487 Views)

Re: Tapered Coil

11-05-2012 05:25 AM in reply to: EdwardCChamberlain

Edward,

Welcome to the forum.

Have you tried using the coil command under the Model tab?

coil.JPG

Best Regards,
Scott McFadden
Inventor Professional 2013
(Colossians 3:23-25)

Distinguished Contributor
Mark.Downes
Posts: 108
Registered: ‎11-18-2010
Message 3 of 12 (471 Views)

Re: Tapered Coil

11-05-2012 06:19 AM in reply to: EdwardCChamberlain

Hi,

 

this is an old technique used on other software but works. 3D sketch a helix, 2D sketch a profile shape, surface sweep a line and project the intersect for your new path.

 

Hope this helps

 

Cheers

Mark

 

Inventor 2013

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 4 of 12 (462 Views)

yes, and i have even used the taper bit of that but the p...

11-05-2012 06:41 AM in reply to: EdwardCChamberlain

yes, and i have even used the taper bit of that but the problem i have is that it creates a taper that comes out at an exact angle from the origin in a straight line. I need the taper to come out and taper along a curve.

 

another way of saying it would be that it tapers at 10deg which then gradually decreases to 5deg as the spiral increases.This would create a shape like a flower bud or light bulb. 

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 5 of 12 (461 Views)

I will have a go at this later and see if i can get it to...

11-05-2012 06:42 AM in reply to: Mark.Downes

I will have a go at this later and see if i can get it to work :smileyhappy: will report back

*Expert Elite*
JDMather
Posts: 26,141
Registered: ‎04-20-2006
Message 6 of 12 (442 Views)

Re: I will have a go at this later and see if i can get it to...

11-05-2012 07:12 AM in reply to: EdwardCChamberlain

EdwardCChamberlain wrote:

I will have a go at this later and see if i can get it to work :smileyhappy: will report back



If you can't get it worked out - attach your attempt here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 7 of 12 (422 Views)

Re: Tapered Coil

11-05-2012 10:14 AM in reply to: EdwardCChamberlain

im struggling to create the surface sweep. 

 

If you could make a video, or series of screen shots of the steps it would be brillient :smileyhappy: 

 

Thanks Ed. 

*Expert Elite*
Cadmanto
Posts: 3,175
Registered: ‎12-07-2011
Message 8 of 12 (419 Views)

Re: Tapered Coil

11-05-2012 10:21 AM in reply to: EdwardCChamberlain

Do you have an image if what you are trying to model?

Best Regards,
Scott McFadden
Inventor Professional 2013
(Colossians 3:23-25)

*Expert Elite*
JDMather
Posts: 26,141
Registered: ‎04-20-2006
Message 9 of 12 (417 Views)

Re: Tapered Coil

11-05-2012 10:32 AM in reply to: EdwardCChamberlain

EdwardCChamberlain wrote:

im struggling to create the surface sweep. 

 

 

Thanks Ed. 


Attach something here. Anything you have attempted.

2d sketch

Line
Coil
Surface Output
Pitch and Height (or similar)

exit sketch

 

3d Sketch

intersection

 

Sweep

 

(see attached example)

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 10 of 12 (411 Views)

Re: Tapered Coil

11-05-2012 10:46 AM in reply to: JDMather

Ok heres what im trying to create and a how far a can get. Notice how the end tapers out? i want to create that but with much more of curved taper

 

Im able to create the surface revolve then create a revolved solid but i cant get any of the componants to line up, for example the helix is allways wonky and wont snap to an axis? Also dont understand "3D intersection"

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube