Inventor General

Reply
*Johnson, Bob
Message 1 of 4 (40 Views)

Sheetmetal holes?

40 Views, 3 Replies
12-10-2002 02:15 PM
Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
selected at the same time and with the same diameter. How can I change the
diameter of only one of the holes? TIA, Bob
*Keller, Kent
Message 2 of 4 (40 Views)

Re: Sheetmetal holes?

12-10-2002 03:04 PM in reply to: *Johnson, Bob
Rmb on the hole in the browser, and edit. Hold the control key and select
the one you want different to remove it from the rest that are selected. Ok
to finish the edit, then rmb on the sketch in the browser for the holes and
share it. Now add another hole using the point that you removed from the
other hole set.
--
Kent Keller
Member of the Autodesk Discussion Forum Moderator Program

http://www.MyMcad.com/KWiK/Mcad.htm

"Bob Johnson" wrote in message
news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYIadrTaRb...
> Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
> selected at the same time and with the same diameter. How can I change the
> diameter of only one of the holes? TIA, Bob
>
>
*Johnson, Bob
Message 3 of 4 (40 Views)

Re:

12-11-2002 01:43 AM in reply to: *Johnson, Bob
Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
key/select hole center point/OK, select hole tool, enter new hole size/OK?
Thanks again, Bob
"Kent Keller" wrote in message
news:88CEF94E0ADD9B27E6DFB81B296523DC@in.WebX.maYIadrTaRb...
> Rmb on the hole in the browser, and edit. Hold the control key and select
> the one you want different to remove it from the rest that are selected.
Ok
> to finish the edit, then rmb on the sketch in the browser for the holes
and
> share it. Now add another hole using the point that you removed from the
> other hole set.
> --
> Kent Keller
> Member of the Autodesk Discussion Forum Moderator Program
>
> http://www.MyMcad.com/KWiK/Mcad.htm
>
> "Bob Johnson" wrote in message
> news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYIadrTaRb...
> > Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern,
all
> > selected at the same time and with the same diameter. How can I change
the
> > diameter of only one of the holes? TIA, Bob
> >
> >
>
>
*Keller, Kent
Message 4 of 4 (40 Views)

Re:

12-11-2002 02:05 AM in reply to: *Johnson, Bob
Not if I am following correctly (always suspect that I am not)

AFAIK you can not have two hole sizes on a sketch unless the sketch is shared. It sounds
to me like that is what you are trying to do. If you just share the sketch then
everything will be happy.

--
Kent
Member of the Autodesk Discussion Forum Moderator Program


"Bob Johnson" wrote in message
news:E607262317971A6A1E0E5AD969846BA2@in.WebX.maYIadrTaRb...
> Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
> key/select hole center point/OK, select hole tool, enter new hole size/OK?
> Thanks again, Bob

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube