Inventor General

Reply
Contributor
aaddekrom
Posts: 18
Registered: ‎02-18-2011
Message 1 of 15 (544 Views)
Accepted Solution

Sheet metal Problem

544 Views, 14 Replies
11-09-2012 03:08 AM

Can't seem to find a sheet metal solution for this part.

Can someone help me in the right direction ?

Tried Rip & Bend and building it from face, solids etc.

IVP2013

*Expert Elite*
karthur1
Posts: 4,149
Registered: ‎04-27-2005
Message 2 of 15 (507 Views)

Re: Sheet metal Problem

11-09-2012 10:14 AM in reply to: aaddekrom

I would say to use a contoured flange to get the basic shape, then add the flanges on the sides.

 

If you want to use what you have so far, you will have to add fillets (inside and outside) and add cuts where the flanges miter together.

 

2012-11-09_1213.png

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 3 of 15 (502 Views)

Re: Sheet metal Problem

11-09-2012 10:23 AM in reply to: karthur1

Not sure how the part was made but it sounds like it was extruded not using shet metal functions.

But putting in radius is not a way to fix it.

 

in sheet metal there is a command called Bend use that just pick the edge you want. it will make it a bend with the sheet metal radius.

 

bend1.JPG

 

bend2.JPG

 

bend3.JPG


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Expert Elite*
karthur1
Posts: 4,149
Registered: ‎04-27-2005
Message 4 of 15 (496 Views)

Re: Sheet metal Problem

11-09-2012 10:40 AM in reply to: jletcher

What is this you are clicking?

 

2012-11-09_1237.png

 

 

I dont recognize that.  I am on 2013.

 

When I try the Bend command, I get an error when I apply it "Failed to extend body or create space for bend".

 

Distinguished Contributor
lama
Posts: 121
Registered: ‎09-06-2006
Message 5 of 15 (491 Views)

Re: Sheet metal Problem

11-09-2012 10:55 AM in reply to: aaddekrom

I had never used the bend feature before to do this, but I tried it on '13 and it worked for me.

Sheet Metal Bend.PNG

Larry Marshall
2013 Product Design Suite Ultimate
Windows 7 Sp1
Intel(R) Core (TM) i5-2400 @ 2.00GHz
6.00 GB of RAM
AMD Radeon HD 6570
*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 6 of 15 (476 Views)

Re: Sheet metal Problem

11-09-2012 12:12 PM in reply to: karthur1

sounds like your radius may be to big or flange to small to accept radius. can you post picture of yours? When it is in preview. like my second picture.


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 7 of 15 (475 Views)

Re: Sheet metal Problem

11-09-2012 12:13 PM in reply to: jletcher

oh also the thickness has to match the sheet metal rule you are using.


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Expert Elite*
JDMather
Posts: 26,141
Registered: ‎04-20-2006
Message 8 of 15 (426 Views)

Re: Sheet metal Problem

11-10-2012 05:49 AM in reply to: aaddekrom

I haven't gotten around to your solution yet, but you might want to take a look at the attached file.

It looked to me like you were doing too much work.

 

simple geometry.png

 

The finished sheet metal part is not so easy.  I see lots of suggestions - but no solution files.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
aaddekrom
Posts: 18
Registered: ‎02-18-2011
Message 9 of 15 (364 Views)

Re: Sheet metal Problem

11-12-2012 05:21 AM in reply to: JDMather

Thanks for your help.

I tried several "modeling" approaches until i decided to model it from surfaces.

Contour flange, Face & Fold, 3D solid & shell give (almost) the same geometry but the problem occurs when developing the flanges.

When i decide to cut and bend after solid & shell, it won't take all bends and cuts.

When i go with Face & Fold (see attachement), it won't make corner seams like it should, because there is always al little angle between the flanges. (The same with contour flange).

 

Regards,

Aad 

*Expert Elite*
JDMather
Posts: 26,141
Registered: ‎04-20-2006
Message 10 of 15 (358 Views)

Re: Sheet metal Problem

11-12-2012 05:34 AM in reply to: aaddekrom

I would very rarely use Fold feature.

I will try to post one solution later today.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube