Inventor General

Reply
Distinguished Contributor
Posts: 136
Registered: ‎03-07-2012
Message 1 of 4 (280 Views)

Sheet Metal - Creating "Postform" Features & Excluding from Flat Pattern

280 Views, 3 Replies
08-02-2012 05:41 AM

Hey everyone:

 

I've read up on some threads on this and didn't seem to find a definite answer either way, so I thought I'd start another thread on it. 

 

Let's say that I'm making a simple L bracket.  I'm going to form it, and machine the holes in both ends *after* forming.  So I don't want the holes to show in my flat pattern. 

 

On the few threads I found, the consensus seemed to be that you may have to have the part file contain no holes and put them in as assembly.  So I just accepted this that it must not be able to be done.

 

Then I ran across a piece of promo literature online from AutoDesk that made mention of the ability to create "postform" features that obviously are created after the forming process.

 

Any ideas how to do this?

 

Thx!

********************************************************
Inventor 2014 64-bit SP1
Win 7 Pro 64-bit SP1
*Expert Elite*
Posts: 25,244
Registered: ‎04-20-2006
Message 2 of 4 (274 Views)

Re: Sheet Metal - Creating "Postform" Features & Excluding from Fl

08-02-2012 06:17 AM in reply to: tdswanson

I would use Derived Component rather than assembly unless that is the way it is really made drilling holes through mating parts at assembly level.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2014 Edu 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Distinguished Contributor
Posts: 136
Registered: ‎03-07-2012
Message 3 of 4 (260 Views)

Re: Sheet Metal - Creating "Postform" Features & Excluding from Fl

08-02-2012 02:36 PM in reply to: JDMather

I'm not familar with the derived component process.  From what little I've read on it, I don't really understand how it applies to this situation.  Can you enlighten me a little with a workflow process?

 

Thanks!

********************************************************
Inventor 2014 64-bit SP1
Win 7 Pro 64-bit SP1
Product Support
Posts: 202
Registered: ‎10-29-2008
Message 4 of 4 (221 Views)

Re: Sheet Metal - Creating "Postform" Features & Excluding from Fl

08-08-2012 06:25 AM in reply to: tdswanson

I agree with creating the blank formed sheet metal part then creating a derived component. To do that you would create your new sheet metal formed part then save it. Start a new file and exit the sketch. Then in the Manage tab of your ribbon under insert you will find the Derive command select it. When asked which file select your formed sheet metal part. Now the file is linked back to the formed sheet metal part (with no holes) and you can now add the holes to the part. Any changes to the formed part will show up in the derived part.

 

Note: if you want to flatten the derived part you will need to set it up as a sheet metal part and use the same styles as you did in the formed part.

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube