Inventor General

Reply
Distinguished Contributor
jdavis417
Posts: 297
Registered: ‎11-19-2008
Message 1 of 13 (377 Views)
Accepted Solution

Part representation in drawing... can it be a symbol?

377 Views, 12 Replies
09-14-2012 11:25 AM

Perhaps I'm confusing Substiute LOD's and some feature of the Punch representation?????

 

I need to show column locations in a Plan (overhead) view.  The columns are so small that they don't show up very well.  Is there an "automagic" (I'd prefer not to have to manually place some kind of sketched symbol on each columns linework) way to do a PART REP (so-called) in a drawing?

 

I'm using 2012 Premium.

 

Thanks In Advance (TIA),

John

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 2 of 13 (370 Views)

Re: Part representation in drawing... can it be a symbol?

09-14-2012 12:10 PM in reply to: jdavis417

Not sure what you are asking do you  have a pic that I may get a better understanding?


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
Distinguished Contributor
jdavis417
Posts: 297
Registered: ‎11-19-2008
Message 3 of 13 (362 Views)

Re: Part representation in drawing... can it be a symbol?

09-14-2012 12:21 PM in reply to: jletcher

Surely (huh, don't call you Shirley?)!

 

Perhaps I've though of a few reasons why this might not be possible...???

Such "substitution" in Plan view might work okay, but what about a Profile???

 

Anywho, the attached image show the Sketched Symbol placed on the column linework to increase it's visibility.

 

Thanks again,

 

John

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 4 of 13 (359 Views)

Re: Part representation in drawing... can it be a symbol?

09-14-2012 12:27 PM in reply to: jdavis417

OK just so I am thinking right the red dots are the column in question correct?


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
Distinguished Contributor
jdavis417
Posts: 297
Registered: ‎11-19-2008
Message 5 of 13 (357 Views)

Re: Part representation in drawing... can it be a symbol?

09-14-2012 12:35 PM in reply to: jletcher

In the words of Ed McMahon, "You are correct, sir. (hic)".

:smileylol:

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 6 of 13 (348 Views)

Re: Part representation in drawing... can it be a symbol?

09-14-2012 12:53 PM in reply to: jdavis417

Well I have not found a way but this is what we do for a work around when I was doing buildings. I have a sketch that is in my master beam and in the IDW I show the sketch not the best way but a way that has worked for us.

 

Mod sketch.JPG

 

Beam sketch.JPG


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
Distinguished Contributor
jdavis417
Posts: 297
Registered: ‎11-19-2008
Message 7 of 13 (276 Views)

Re: Part representation in drawing... can it be a symbol?

10-04-2012 09:41 AM in reply to: jletcher

James,

 

Thanks again.  I've marked this as a "solution", but now am having difficulty getting the sketch to show in my drawings...

it's "visible" in the part... 

 

What am I missing?  Any suggestions?

 

thanks,

 

John

*Expert Elite*
JDMather
Posts: 26,141
Registered: ‎04-20-2006
Message 8 of 13 (268 Views)

Re: Part representation in drawing... can it be a symbol?

10-04-2012 09:49 AM in reply to: jdavis417

jdavis417 wrote:

... but now am having difficulty getting the sketch to show in my drawings...

it's "visible" in the part... 


This question has come up 3 times today.

http://forums.autodesk.com/t5/Autodesk-Inventor/retrieve-a-bend-from-sweep/td-p/3646098

 

very rare for it to come up at all.  What's going on today?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 9 of 13 (260 Views)

Re: Part representation in drawing... can it be a symbol?

10-04-2012 09:59 AM in reply to: jdavis417

Just right click on the part in the browser show sketch. or you can change your select options  to parts and pick them from the view (faster) in view left click part then right click get sketches.


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
Distinguished Contributor
jdavis417
Posts: 297
Registered: ‎11-19-2008
Message 10 of 13 (241 Views)

Re: Part representation in drawing... can it be a symbol?

10-04-2012 11:50 AM in reply to: jletcher

That's what I thought... that's what I tried... it works SOMETIMES.

 

sometimes.png

 

I'm in 2012.  Any idea why it's not consistent?

 

Also, in JDMather's example he shows an "Enable" option when right-clicking on the (non-visible) sketch.  In the drawing environment, a sketch in a part does not EVER appear in the history browser for me.  What gives?

 

Thanks to all,

 

John

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube