Inventor General

Reply
Contributor
Johnnyjack777
Posts: 13
Registered: ‎02-17-2011
Message 1 of 5 (463 Views)

Inventor Crashes on Simple Spline Extrude?

463 Views, 4 Replies
10-20-2012 08:27 PM

Curious... what the heck?

 

Crashes on a simple extrusion... VERY basic spline...

(When I click extrude... I doubt it's even a complete closed shape yet)

 

any thoughts?

Valued Mentor
Valued Mentor
wh
Posts: 388
Registered: ‎12-27-2003
Message 2 of 5 (451 Views)

Betreff: Inventor Crashes on Simple Spline Extrude?

10-20-2012 11:34 PM in reply to: Johnnyjack777

Set additional lines to construction lines, and it's ok.

 

Walter

*Expert Elite*
JDMather
Posts: 26,148
Registered: ‎04-20-2006
Message 3 of 5 (435 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-21-2012 07:41 AM in reply to: Johnnyjack777

Just took a look back through your previous posts here.
I don't see any improvement in your sketching techniques.
I recommed you read this document.

http://home.pct.edu/~jmather/AU2007/MA105-1L%20Mather.pdf

 

by this point you have probably developed bad habits that will be hard to break.

 

Find the Origin Center Point and use it.

Use Construction lines where appropriate (this was pointed out to you on an earlier problem).

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Employee
Yijiang.Cai
Posts: 350
Registered: ‎05-20-2008
Message 4 of 5 (409 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-21-2012 08:04 PM in reply to: Johnnyjack777

When using the dataset to extrude it, there is no crash seen. Maybe there are some key steps I missed. So could make more comments about the steps or workflow?

Thanks,
River Cai

Inventor Quality Assurance Team
Autodesk, Inc.
*Expert Elite*
JDMather
Posts: 26,148
Registered: ‎04-20-2006
Message 5 of 5 (379 Views)

Re: Inventor Crashes on Simple Spline Extrude?

10-22-2012 05:12 AM in reply to: Yijiang.Cai

Note that iProperties indicates the file is r2010 apparently with no Service Packs installed.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube