Community
Inventor Forum
Welcome to Autodesk’s Inventor Forums. Share your knowledge, ask questions, and explore popular Inventor topics.
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Ellipse trim bug?

4 REPLIES 4
Reply
Message 1 of 5
Anonymous
408 Views, 4 Replies

Ellipse trim bug?

File in CF.

What I'm trying to do is set up a sketch with ellipse and radial lines for
projection to new sketches which will be elliptical segments. The radials are
projected, an ellipse sketched using the radials and then trimmed. When
trimmed the ellipse segment goes red (can't solve constraints?).

Thanks,
Jeff
=============================
4 REPLIES 4
Message 2 of 5
Anonymous
in reply to: Anonymous

I'm probably not interpreting what you are doing correctly, but I patterned
some radial lines, made an ellipse on one and trimmed it. Offset a couple of
workplanes and projected successive lines to them drawing and trimming the
ellipses and didn't see any errors. If you want to post what it is you're
trying to do exactly, I could see what I misunderstood.
~Larry


"Jeff Howard" wrote in message
news:DF055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaRb...
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
Message 3 of 5
Anonymous
in reply to: Anonymous

Oh ... it was already there. I didn't get the same result. Mine trimmed
okay. See CF.
~Larry

"Jeff Howard" wrote in message
news:DF055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaRb...
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
Message 4 of 5
Anonymous
in reply to: Anonymous

I opened your file in the RTM build, and the ellipse segment was green.

Loren Jahraus
Autodesk Inventor Workflow Team

"Jeff Howard" wrote in message
news:DF055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaRb...
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
Message 5 of 5
Anonymous
in reply to: Anonymous

Thanks for looking, guys.

That's good news, Loren.

Jeff
====================

"Loren Jahraus (Autodesk)" wrote in message
news:D3C56529BA8E3B989C808A084367D544@in.WebX.maYIadrTaRb...
I opened your file in the RTM build, and the ellipse segment was green.

Loren Jahraus
Autodesk Inventor Workflow Team

Can't find what you're looking for? Ask the community or share your knowledge.

Post to forums  

Autodesk Design & Make Report