Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
Show only
|
Search instead for
Did you mean:
This page has been translated for your convenience with an automatic translation service. This is not an official translation and may contain errors and inaccurate translations. Autodesk does not warrant, either expressly or implied, the accuracy, reliability or completeness of the information translated by the machine translation service and will not be liable for damages or losses caused by the trust placed in the translation service.Translate
I have never seen that before. Thanks for sharing Could you get it
to work properly or did you have to re-sketch the rectangle?
"Kent Keller" wrote in message
news:7080B49656406A7162BC424B645C7055@in.WebX.maYIadrTaRb...
> I placed a real small avi of the results of adding sketch fillets to a
rectangle. Seems
> like it shouldn't do that to me. 8^)
>
> --
> Kent
> Assistant Moderator
> Autodesk Discussion Forum Moderator Program
>
>
>
Kent, off subject shssssss what software do you need for making these
AVI's? Ta
--
Laurence,
Power is nothing without Control
---
"Kent Keller" wrote in message
news:7080B49656406A7162BC424B645C7055@in.WebX.maYIadrTaRb...
> I placed a real small avi of the results of adding sketch fillets to a
rectangle. Seems
> like it shouldn't do that to me. 8^)
>
> --
> Kent
> Assistant Moderator
> Autodesk Discussion Forum Moderator Program
>
>
>
I mainly use Hypercam http://www.hyperionics.com/
Many people use Snagit. www.snagit.com
and Sean found this the other day http://www.vrtainment.com/vrtainment_web/intro/intro.htm
--
Kent
Assistant Moderator
Autodesk Discussion Forum Moderator Program
"Laurence Yeandle" wrote in message
news:A1E6FCAA0C547844545410E645BB8F2B@in.WebX.maYIadrTaRb...
> Kent, off subject shssssss what software do you need for making these
> AVI's? Ta
>
> --
> Laurence,
>
> Power is nothing without Control
> ---
>
>
> "Kent Keller" wrote in message
> news:7080B49656406A7162BC424B645C7055@in.WebX.maYIadrTaRb...
> > I placed a real small avi of the results of adding sketch fillets to a
> rectangle. Seems
> > like it shouldn't do that to me. 8^)
> >
> > --
> > Kent
> > Assistant Moderator
> > Autodesk Discussion Forum Moderator Program
> >
> >
> >
>
>
I had a construction line going from a projected point to the middle of the edge (both
corners on that edge did it) of the rectangle. I deleted that line, added the fillets and
then added the line back.
It is pretty repeatable. I will post a small example sketch in IVCF. This one it
appears to only be the top right that has the problem.
--
Kent
Assistant Moderator
Autodesk Discussion Forum Moderator Program
"Jimmy Carr" wrote in message
news:BFCF5E7B5140D30A3C1F554A4096C134@in.WebX.maYIadrTaRb...
> I have never seen that before. Thanks for sharing Could you get it
> to work properly or did you have to re-sketch the rectangle?
Ah ... you found the mid-point constraint thingy. I try to do fillets or
something that will change one side of the line before doing the mid-point
constraints, but I forget a lot.
~Larry
"Kent Keller" wrote in message
news:7080B49656406A7162BC424B645C7055@in.WebX.maYIadrTaRb...
> I placed a real small avi of the results of adding sketch fillets to a
rectangle. Seems
> like it shouldn't do that to me. 8^)
>
> --
> Kent
> Assistant Moderator
> Autodesk Discussion Forum Moderator Program
>
>
>
"Kent Keller" wrote in message
news:64C39FF7B0B2BE5C5A5C9E74EF526C4B@in.WebX.maYIadrTaRb...
> I mainly use Hypercam http://www.hyperionics.com/
> Many people use Snagit. www.snagit.com
> and Sean found this the other day
http://www.vrtainment.com/vrtainment_web/intro/intro.htm
>
> --
> Kent
It works right if you use mirror constraints instead of the midpoint, since
the horizontal tanget line doesn't need to shift to meet the constraint.
--
Kevin Wehner
724.941.9704-3019
SKC Inc.
863 Valley View Road
Eighty-Four, PA 15330
"Kent Keller" wrote in message
news:7080B49656406A7162BC424B645C7055@in.WebX.maYIadrTaRb...
> I placed a real small avi of the results of adding sketch fillets to a
rectangle. Seems
> like it shouldn't do that to me. 8^)
>
> --
> Kent
> Assistant Moderator
> Autodesk Discussion Forum Moderator Program
>
>
>
![Autodesk Design & Make Report](https://forums.autodesk.com/t5/image/serverpage/image-id/1350519iCB55845EBFC43016/image-size/large?v=v2&px=999" "Autodesk Design & Make Report")