Inventor General

Reply
Member
Hodman
Posts: 5
Registered: ‎10-04-2012
Message 1 of 4 (207 Views)

Continual random crashes

207 Views, 3 Replies
10-08-2012 03:27 PM

Sorry I was unable to configure a transfer from Factory Design Suite Group. This is more appropriate here.

 

Help?

Approx August, Inventor 2013 started to randomly crash.

Until then it was working fine.

Service packs & several re-installs have not cured it.

I cannot replicate the process.

I am lucky if I get 20 minutes of operation.

One day it actually ran all day. The next it crashed maybe 20 times.

Several projects have only needed 2D work which works fine but I have run out of time to postpone the Inventor projects.

Is anyone else having similar mysteries?

*Expert Elite*
blair
Posts: 3,934
Registered: ‎11-13-2006
Message 2 of 4 (195 Views)

Re: Continual random crashes

10-08-2012 09:17 PM in reply to: Hodman

No.

 

Don't know where to start as we don't have a single clue as to your operating system and system spec's, so all we can post is the generic basic help.

 

1.) Does your hardware meet the minimum requirements as in the Autodesk Hardware requirements?

2.) Did you install the software with a minimum of Power-User (preferable Administrator) rights?

3.) If Vista/Win7, did you have the UAC slider set to it's lowest level?

4.) Did you disable your Anti-Virus software (assuming you have A-V installed)?

5.) You have installed all applicable hot-fixes for your O/S as well as for your software, includes graphics card drivers?

6.) Are your files stored locally or on a network?

7.) You didn't get a virus or malware on your system around the August date?

8.) Check your system for any changes or installed software or updates.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Member
Hodman
Posts: 5
Registered: ‎10-04-2012
Message 3 of 4 (193 Views)

Re: Continual random crashes

10-08-2012 09:26 PM in reply to: blair

Thanks Blair I wasn't sure which info to actually send, so now I will step through each of those steps and return with a summary (as soon as I have time). Thanks again

 

Edited by
Discussion_Admin

Member
Hodman
Posts: 5
Registered: ‎10-04-2012
Message 4 of 4 (118 Views)

Re: Continual random crashes

11-08-2012 01:48 PM in reply to: Hodman

Results are in.

 

Due to time constraints I had my IT department do a complete purge of the hard drive.

Now that I have cleaned it all I am now up & running again.

 

thanks for anyone that may have considered my challenge.

 

 

Cheers

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube