Inventor General Discussion

Reply
Valued Contributor
trenthoskings
Posts: 70
Registered: ‎11-25-2011
Message 1 of 6 (201 Views)

tube % pipe versus individual pipes

201 Views, 5 Replies
12-16-2012 03:44 AM

I habe a machine which required various size pipes.The machine area is 7m x 2m.....I ususally design each individual pipe...is this better to do with pipe and tube or should i continue to create each pipe individually....I have created all the valves which i use in the machines......can these be inserted using Pipe & Tube?

 

Any advantage of pipe and tube over individual creation of pipes in machines of this size

 

Thank you

 

TH

*Expert Elite*
blair
Posts: 3,964
Registered: ‎11-13-2006
Message 2 of 6 (186 Views)

Re: tube % pipe versus individual pipes

12-16-2012 09:55 AM in reply to: trenthoskings

The T&P module is really just a "short-cut" and has some specific tools to aid in 3D sketching for the create of the T&P runs.

 

If you are just using straight pipes and have placed all your fittings, maybe think of using the Content Center for your pipes. You can simply RMB on the CC pipe within the assembly and change it's size or length from the screen pop-up dialogue box.

 

It also has a number of benefits in the IDW's BOM as well.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
*Expert Elite*
cbenner
Posts: 3,182
Registered: ‎04-06-2010
Message 3 of 6 (157 Views)

Re: tube % pipe versus individual pipes

12-17-2012 06:38 AM in reply to: trenthoskings

In my humble opinion, the benefits of T&P vs individual pipes using standard constraints depends greatly on the amount of piping you need to run.  If your machine is heavily piped as ours are, they are a nightmare to do with standard constraints.  T&P does have some limitations and can be a hair pulling experience at times... but there's no way I'd go back with the amount of piping we do on a daily basis.  And yes, your custom valves and fittings can be authored and added to the Content Center to be used with Tube & Pipe fairly easily.

 

So it all depends on the nature and amout of piping you need to do.

ChrisB

ADSK_Expert_Elite_Icon_S_Color_Blk.png

Please use Mark Solutions!.Accept as Solution &Give Kudos!Kudos to further enhance the value of these forums. Thank you! :smileyhappy:

http://cbennertipstricks.blogspot.com/


   

Valued Contributor
trenthoskings
Posts: 70
Registered: ‎11-25-2011
Message 4 of 6 (136 Views)

Re: tube % pipe versus individual pipes

12-17-2012 12:04 PM in reply to: cbenner

Thanks Blair

 

Hi Chris

 

Thank you

 

Would you have a picture of your machines

 

Thanks again

 

Tony

*Expert Elite*
blair
Posts: 3,964
Registered: ‎11-13-2006
Message 5 of 6 (130 Views)

Re: tube % pipe versus individual pipes

12-17-2012 12:21 PM in reply to: trenthoskings

We do commercial transport trailers, so most of our T&P is flexible lines.

 

Image.jpg

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Valued Contributor
trenthoskings
Posts: 70
Registered: ‎11-25-2011
Message 6 of 6 (121 Views)

Re: tube % pipe versus individual pipes

12-17-2012 01:51 PM in reply to: trenthoskings

very impressive

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube