Inventor General Discussion

Reply
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 1 of 6 (212 Views)
Accepted Solution

connector + hose

212 Views, 5 Replies
11-16-2012 05:57 AM

Is there another way of doing this other then using the pipe and run tools.There are 6  x 10mm connectors.I want to run 10mm plastic tube from the bottom 3 connectors up to the top 3 connectors.Please how can this be done other then using pipe and tube tools?

 

Regards

Terry

 

By the way is this simple if using the pipe and run tools?

Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 2 of 6 (184 Views)

Re: connector + hose

11-17-2012 04:37 AM in reply to: Terry__Close

Is this only achievable by using the Tube & Pipe tools?

 

Terry

*Expert Elite*
JDMather
Posts: 26,301
Registered: ‎04-20-2006
Message 3 of 6 (179 Views)

Re: connector + hose

11-17-2012 05:35 AM in reply to: Terry__Close

If you don't want to use Routed Systems then simple start a new part in the context of the assembly.

Project Geometry a connection point (like a circle or similar) from each connector.

This will make the new part adaptive to the position of the connectors.

Create 2D or 3D sketch for your tube run and Sweep.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 4 of 6 (174 Views)

Re: connector + hose

11-17-2012 05:40 AM in reply to: JDMather

Thanks...i`m new to what you suggest...could you give an example of how you would do this or could you add the hoses to the conectors i attached in my first post...

Is there any difference between the way you explained to do this and the Routed system.

 

Thanks

*Expert Elite*
JDMather
Posts: 26,301
Registered: ‎04-20-2006
Message 5 of 6 (170 Views)

Re: connector + hose

11-17-2012 06:08 AM in reply to: Terry__Close

Terry__Close wrote:

Is there any difference between the way you explained to do this and the Routed system.

 

Thanks


This is basically what Routed Systems does - but it has tools that automate the process so that it is fewer steps.

The attached was done in student version - so keep separate from your data and delete after examination of technique.

 

1. Turn on or create connection point in Connectors (I used origin Center Point and logical axis).

2. Create New Part in assembly. (set to constrain to connector part)

3. I like to then exit part and add second constraint to axis of new part and connector.

4. Edit the part and start new sketch and Project Geometry for the tubing profile.
5. Start a 3D sketch and Include Geometry the connection points at both ends of tube.

6. Create lines for straight sections of tubing (if all will be straight I might do these in 2D sketches instead, depending on how tightly I need to control the location).

7. Connect the 2D lines (in my simple case attached) with spline, including as many points in space as needed to control the path (if this is bent tubing I do slightly different with Bends between straight line sections).  Add tangencies to lines at start and end.

8. If you need additional point to the spline you can add them.  You can use the 3D Move/Rotate tool to move points as needed.

9. Sweep the profile.

 

Repeat as needed.

 

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Terry__Close
Posts: 91
Registered: ‎03-26-2011
Message 6 of 6 (149 Views)

Re: connector + hose

11-17-2012 04:39 PM in reply to: JDMather

Thanks JD

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube