Inventor General Discussion

Reply
Distinguished Contributor
dick_upton
Posts: 646
Registered: ‎02-25-2009
Message 1 of 5 (274 Views)

Would gladly give up 3 release's interface changes for one escape command

274 Views, 4 Replies
04-03-2012 10:06 AM

I have lost more time in the last 3 years sitting waiting for Inventor to complete an unwanted, uncancellable command than I will ever make up in all the fancy interface changes that my subscription dollars have brought about.

 

To have an escape key that worked in Inventor, I'd gladly trade for the Inventor 2010 interface.

 

If this request, made repeatedly by many over the last, oh, 8 to 10 years, is not possible, it would be nice to know why.

*Expert Elite*
dan_inv09
Posts: 2,300
Registered: ‎12-12-2006
Message 2 of 5 (245 Views)

Re: Would gladly give up 3 release's interface changes for one escape command

04-03-2012 12:06 PM in reply to: dick_upton

Beyond the need to be able to cancel a command ...

 

Has anyone's productivity been improved by any of the interface changes?

 

Aside from the break-in time where you have no clue how to do things that were all but automatic before, the ribbon is just terrible. At best it adds at least one click to everything you do - seriously it was all there in the panel bar and someone comes along and says, "I know what will help, let's hide some of it on different tabs!"

 

And do not even get me started on the icons.

Valued Mentor
IgorMir
Posts: 481
Registered: ‎08-02-2003
Message 3 of 5 (207 Views)

Re: Would gladly give up 3 release's interface changes for one escape command

04-03-2012 06:09 PM in reply to: dan_inv09

Totally agree with you, Dan! And yet nothing we can do about it. The imbeciles are running the show in Autodesk Inventor team nowdays. Those, who knows better - they don't have any power to say anything. Which is most unfortunate. 

Web: www.meqc.com.au
Active Contributor
IS200
Posts: 34
Registered: ‎06-06-2011
Message 4 of 5 (205 Views)

Re: Would gladly give up 3 release's interface changes for one escape command

04-03-2012 06:35 PM in reply to: dick_upton
Forget about the Ribbon arguement, everything has gone that way and it is OK when you get used to it.

However, I fully agree with you regarding the necessity for a properly functioning escape command. I too have lost many hours over the years waiting for Inventor to recalculate a solution when I realise I have made a mistake, or could have done it a better way. Why can't I just 'bail out' and go back to where I was. Why must I wait, and wait, and wait so I can then press undo and wait, and wait to get back to where I was in the first place?

Why can't we have the escape key that actually tells Inventor to stop the current calculation and just drop me back to where I was?

Distinguished Contributor
dick_upton
Posts: 646
Registered: ‎02-25-2009
Message 5 of 5 (143 Views)

Re: Would gladly give up 3 release's interface changes for one escape command

04-05-2012 06:12 AM in reply to: dick_upton

Would any Autodeskee care to comment on why the much requested Escape key enhancement has thusfar been ignored or neglected in deferrence to multiple rounds of interface development?

 

Just a straight simple answer and we'll be happy to wait until it can be added. I see 2013 does not have this but I can RMB and move the EOP marker, and delete multiple sheets at a time WOOPDEEDOO. <sarcasm mode off>

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube