Inventor General Discussion

Reply
Active Member
classicac
Posts: 8
Registered: ‎06-01-2011
Message 1 of 9 (340 Views)

Text below angular dimensions

340 Views, 8 Replies
10-03-2012 04:38 AM

Hello All

 

what I am needing help with is, is it possible to have text below the angular dimension line like you can with most other dimensions. The attached pic shows my 10 dimension with the typ. Under the line and my 30 dimension with typ. Under the line but the typ. Under the 30 is just a text box I eye-balled in to place it is not attached to the dimension. I looked in the styles editor but could not find the setup option I need. Any suggestions?

 

Cheers

 

Andy

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 2 of 9 (332 Views)

Re: Text below angular dimensions

10-03-2012 04:48 AM in reply to: classicac

Don't use TYP. If you tried to use that at my last job you would be fired. :smileyhappy:

 

But to answer your question yes. This is one setting

 

52.JPG

 

But if you go to your style and standard in that Dimension Style and change it to Inline-Aligned you will get the look you want.

 

Inline.JPG

 

This will give you this

 

new.JPG

 

Oh just incase all you have to do is dbl click on the Dimension then type it in

ty.JPG


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
Active Member
classicac
Posts: 8
Registered: ‎06-01-2011
Message 3 of 9 (317 Views)

Re: Text below angular dimensions

10-03-2012 05:45 AM in reply to: jletcher

Thanks for the reply James, I did notice the inline aligned option but as you see it cuts through the dim line, and like you said about the TYP. the drawing office can be real picky when it comes to things like this.

 

Thanks again

Andy

*Expert Elite*
mrattray
Posts: 2,470
Registered: ‎09-13-2011
Message 4 of 9 (313 Views)

Re: Text below angular dimensions

10-03-2012 05:50 AM in reply to: classicac

That's funny, the checkers at my office are in love with typ. I never like to use it myself, I either just dimension everything individually or use a x places note. I actually had a print returned to me with my "extra" dimensions crossed off and typs written in! :smileytongue:

Mike (not Matt) Rattray

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 5 of 9 (304 Views)

Re: Text below angular dimensions

10-03-2012 06:10 AM in reply to: mrattray

Well just for information TYP. Is not allowed in DOD drawings its 2X, 3X .... If they see TYP. You will get your drawings back and months of audits that will cost you tons of money. You can't even use abbreviations in DOD drawings like QTY. 

 

It was explained to me why TYP. Is not to be used on drawings but I can't remember the reason but at the time it made sense..... 


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 6 of 9 (297 Views)

Re: Text below angular dimensions

10-03-2012 06:14 AM in reply to: classicac

Then use this one

Parallel.JPG

 

Gives you this

 

pio.JPG


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 7 of 9 (295 Views)

Re: Text below angular dimensions

10-03-2012 06:17 AM in reply to: jletcher

And if you want it below pick this

out.JPG

 

Give you this

Gives.JPG


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(
*Expert Elite*
mrattray
Posts: 2,470
Registered: ‎09-13-2011
Message 8 of 9 (290 Views)

Re: Text below angular dimensions

10-03-2012 06:19 AM in reply to: jletcher

I understand not allowing TYP, but not allowing QTY? That's silly.

Growing up in the Detroit area I learned drafting in the context of automotive standards, especially Ford since my first job in the industry was with Roush. Ford actually publishes a booklet with all of the official Ford abbreviations to be used, this of course is made to accompany thier encyclopedia sized book of general drafting standards...

Mike (not Matt) Rattray

*Pro
jletcher
Posts: 1,946
Registered: ‎05-18-2011
Message 9 of 9 (288 Views)

Re: Text below angular dimensions

10-03-2012 06:22 AM in reply to: mrattray

Hey I worked for Ford then Chevy then Dodge Back in 1986.. I was the quality control trainer...


Please mark this response as "Accept as Solution" if it answers your question.

James Letcher
2012 Factory Design Suite ( will not load 2013)
What happen to my Inventor :-(

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube