Inventor General Discussion

Reply
Active Contributor
rgitzlaff
Posts: 34
Registered: ‎02-21-2007
Message 1 of 4 (58 Views)

Disappearing command box

58 Views, 3 Replies
03-17-2008 05:37 AM
We have Inventor Professional 2008 and when we activate a command and the command dialog box comes up, it dissapears as soon as you go to choose the first parameter. the box is still there, and buttons reappear one at a time if you slowly move the pointer over them, but it is very annoying. This happens with the constraint dialog in assemblies, my right click box, and others have observed this with all other command boxes. It primarily happens when the box comes up over the display portion of the screen. It seems to work fine however when it comes up covering the command bar portion of the screen. This is happening on multiple computers here that are all set up identically. We have service pack 2 installed. Any ideas? It's not something we can't work around, it's just annoying and slows us down somewhat.
*Blair Stunder
Message 2 of 4 (58 Views)

Re: Disappearing command box

03-17-2008 08:25 AM in reply to: rgitzlaff
Can you supply syetem spec's as well as graphics card driver version.

--
Dell 670 dual Xeon - 3.2
3gb memory, SCSI320-15k
XP-Pro, sp2
Quadro FX3400: Driver: 169.61 Direct3D
IV2008-pro sp2,
SpacePilot Rel V: 3.5.6 Dvr V: 6.5.5 Firmware 3.12

wrote in message news:5877400@discussion.autodesk.com...
We have Inventor Professional 2008 and when we activate a command and the
command dialog box comes up, it dissapears as soon as you go to choose the
first parameter. the box is still there, and buttons reappear one at a time
if you slowly move the pointer over them, but it is very annoying. This
happens with the constraint dialog in assemblies, my right click box, and
others have observed this with all other command boxes. It primarily
happens when the box comes up over the display portion of the screen. It
seems to work fine however when it comes up covering the command bar portion
of the screen. This is happening on multiple computers here that are all
set up identically. We have service pack 2 installed. Any ideas? It's not
something we can't work around, it's just annoying and slows us down
somewhat.
*Blair Stunder
Message 3 of 4 (58 Views)

Re: Disappearing command box

03-17-2008 11:33 AM in reply to: rgitzlaff
Try switching between D3D and OpenGL.

--
Dell 670 dual Xeon - 3.2
3gb memory, SCSI320-15k
XP-Pro, sp2
Quadro FX3400: Driver: 169.61 Direct3D
IV2008-pro sp2,
SpacePilot Rel V: 3.5.6 Dvr V: 6.5.5 Firmware 3.12

"Blair Stunder" wrote in message
news:5877602@discussion.autodesk.com...
Can you supply syetem spec's as well as graphics card driver version.

--
Dell 670 dual Xeon - 3.2
3gb memory, SCSI320-15k
XP-Pro, sp2
Quadro FX3400: Driver: 169.61 Direct3D
IV2008-pro sp2,
SpacePilot Rel V: 3.5.6 Dvr V: 6.5.5 Firmware 3.12

wrote in message news:5877400@discussion.autodesk.com...
We have Inventor Professional 2008 and when we activate a command and the
command dialog box comes up, it dissapears as soon as you go to choose the
first parameter. the box is still there, and buttons reappear one at a time
if you slowly move the pointer over them, but it is very annoying. This
happens with the constraint dialog in assemblies, my right click box, and
others have observed this with all other command boxes. It primarily
happens when the box comes up over the display portion of the screen. It
seems to work fine however when it comes up covering the command bar portion
of the screen. This is happening on multiple computers here that are all
set up identically. We have service pack 2 installed. Any ideas? It's not
something we can't work around, it's just annoying and slows us down
somewhat.
Contributor
torgny.gerthsson
Posts: 11
Registered: ‎04-14-2006
Message 4 of 4 (58 Views)

Re: Disappearing command box

03-17-2008 01:27 PM in reply to: rgitzlaff
I had the same problem. Uninstalled Intellipoint mouse driver and problem was gone.
Autodesk Inventor 2013 Professional
HP EliteBook 8730w Mobile Workstation
8Gb Ram, Nvidia 3700M
Windows 7 Enterprise 64 Edition

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube