Inventor General Discussion

Reply
*Expert Elite*
mrattray
Posts: 2,471
Registered: ‎09-13-2011
Message 1 of 7 (565 Views)
Accepted Solution

Curve Driven Pattern - Multiple Tangent Curves?

565 Views, 6 Replies
10-22-2012 10:58 AM

Is there a way to use the curve driven (rectangular) pattern referencing two tangent curves (an arc and a tangent line). I'd like to be able to create this pattern of slots in one pattern, othrwise I'll have to make two cut features at each end and use one pattern for the straight and another for the curve.

 

Capture.JPG

Mike (not Matt) Rattray

*Expert Elite*
JDMather
Posts: 26,355
Registered: ‎04-20-2006
Message 2 of 7 (560 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-22-2012 11:44 AM in reply to: mrattray

Depends

are they the same distance appart if the curve was layed flat?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
mrattray
Posts: 2,471
Registered: ‎09-13-2011
Message 3 of 7 (557 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-22-2012 11:48 AM in reply to: JDMather

Yes, I would like them to be evenly spaced along the "flat" for the sake of simplicity, but they can be anything because the mating part is being designed and made at the same time.

Mike (not Matt) Rattray

*Expert Elite*
JDMather
Posts: 26,355
Registered: ‎04-20-2006
Message 4 of 7 (547 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-22-2012 12:54 PM in reply to: mrattray

Just for clarity - the part doesn't have to be something folded from a flat - I just wanted to make sure the distance measured along the curve rather than chord center-to-center distance.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
mrattray
Posts: 2,471
Registered: ‎09-13-2011
Message 5 of 7 (545 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-22-2012 01:05 PM in reply to: JDMather

Of course the fact that's it's a flat piece of sheetmetal doesn't matter.

When these are done in AutoCAD they're defined by the angles between their chords. Nobody cares how they get defined in Inventor, though, what is important is that the distances and number of instances can change automatically to reflect changes to those curves. The length of the line and the circumferential length of that arc (and possibly the radius) will be changing.

 

Part file is attached to this post. Before you jump on me for it, I'm right in the middle of trying to get that ugly Sketch11 for the face sorted.

Mike (not Matt) Rattray

*Expert Elite*
JDMather
Posts: 26,355
Registered: ‎04-20-2006
Message 6 of 7 (535 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-22-2012 04:16 PM in reply to: mrattray

Examine technique and then discard (edited in student version).

 

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Expert Elite*
mrattray
Posts: 2,471
Registered: ‎09-13-2011
Message 7 of 7 (515 Views)

Re: Curve Driven Pattern - Multiple Tangent Curves?

10-23-2012 05:08 AM in reply to: JDMather

Ah, that's exactly what I needed. Now that I'm looking at this, I think I remember seeing this trick in your white paper.

Thank you, JD!

Mike (not Matt) Rattray

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube