Inventor General Discussion

Inventor General Discussion

Reply
Active Member
rjones0215
Posts: 9
Registered: ‎10-01-2011
Message 1 of 8 (227 Views)
Accepted Solution

Constraint Virus?

227 Views, 7 Replies
05-02-2012 05:35 AM

For 3 or 4 days now, 90% of the time I place a mate or flush constraint, it automatically offsets to some random direction and I have to reset to zero.  Anyone know what might be causing this?

Inventor 2013 Certified Professional
*Expert Elite*
JDMather
Posts: 26,518
Registered: ‎04-20-2006
Message 2 of 8 (216 Views)

Re: Constraint Virus?

05-02-2012 05:59 AM in reply to: rjones0215

I have never seen this behavior.

Is this with 2013?

 

Do you have Predict Offset enabled?

Can you attach an assembly here that exhibited this behavior (accept the offset constraint - don't reset it to zero).  Only need the parts that are constrained.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Mentor
Martin_Goodland
Posts: 302
Registered: ‎07-15-2005
Message 3 of 8 (214 Views)

Re: Constraint Virus?

05-02-2012 06:00 AM in reply to: rjones0215

In the constraint dialogue box you have ticked the box with an image of a ruler next to it. When ticked if faces are parallel the dimension they are offset by is automatically placed in the offset box.

 

Regards

 

Martin 


PDSU 2014 SP1.3
Windows 7 64bit SP1, Office 2007 Pro
Intel i7 980x, 24 Gb DDR3 RAM
Geforce 580GTX Graphics (Diver 327.23)
256GB SSD OS, 80GB SSD working folder
Space Pilot
Employee
johnsonshiue
Posts: 2,080
Registered: ‎04-30-2008
Message 4 of 8 (204 Views)

Re: Constraint Virus?

05-02-2012 06:08 AM in reply to: rjones0215

Hi! Could you show me an example by providing Inventor files or a video? What release of Inventor are you on?

Thanks!

 



Johnson Shiue (johnson.shiue@autodesk.com)
Principal SQA Engineer, Inventor
Mechanical Design
Autodesk, Inc.

Active Member
rjones0215
Posts: 9
Registered: ‎10-01-2011
Message 5 of 8 (202 Views)

Re: Constraint Virus?

05-02-2012 06:10 AM in reply to: rjones0215

Ha.  Yes, I must have clicked the "Predict Offsets" box.  I didn't even know if was there.  It's unchecked now and everything seems to be back to normal.  Thanks again.

Inventor 2013 Certified Professional
*Expert Elite*
JDMather
Posts: 26,518
Registered: ‎04-20-2006
Message 6 of 8 (190 Views)

Re: Constraint Virus?

05-02-2012 06:55 AM in reply to: rjones0215

Then it should have been 100%  in your original problem description.

Watch out for this one as if your parts are already close to alignment you might not even notice the offset and this is one of the few setting changes that persist after leaving the dialog (I think even after leaving a session of Inventor - but I would have to check on that).

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Active Member
rjones0215
Posts: 9
Registered: ‎10-01-2011
Message 7 of 8 (188 Views)

Re: Constraint Virus?

05-02-2012 06:58 AM in reply to: JDMather

I believe you are correct.  In the future, I will be more cautious of this.

Inventor 2013 Certified Professional
Valued Mentor
Martin_Goodland
Posts: 302
Registered: ‎07-15-2005
Message 8 of 8 (170 Views)

Re: Constraint Virus?

05-02-2012 07:36 AM in reply to: rjones0215

It does persist across sessions (I normally have it turned on). It does only work when the mating faces are aligned though, if there is any rotation then the value remains zero.

 

Regards

 

Martin


PDSU 2014 SP1.3
Windows 7 64bit SP1, Office 2007 Pro
Intel i7 980x, 24 Gb DDR3 RAM
Geforce 580GTX Graphics (Diver 327.23)
256GB SSD OS, 80GB SSD working folder
Space Pilot
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.