Inventor General Discussion

Reply
Member
ben_walker5
Posts: 4
Registered: ‎10-18-2012
Message 1 of 27 (2,181 Views)

Can't move unconstrained parts within an assembly

2181 Views, 26 Replies
11-08-2012 08:40 AM

Hi, I have been building an assembly and suddenly I am unable to move parts according to their constraints. I can move them as soon as they are placed but as soon as I add one constraint it's as if they are glued in place. For example, when I line up two holes I can no longer rotate one part around the grounded component.

 

Have a turned off some functionality of the program?

 

Any help would be much appreciated!

 

Ben

Distinguished Contributor
KF090
Posts: 134
Registered: ‎04-27-2010
Message 2 of 27 (2,136 Views)

Re: Can't move unconstrained parts within an assembly

11-16-2012 01:50 PM in reply to: ben_walker5

I'm having this same problem, hopefully there is an easy quick fix.

*Pro
sbixler
Posts: 1,870
Registered: ‎09-15-2003
Message 3 of 27 (2,114 Views)

Re: Can't move unconstrained parts within an assembly

11-18-2012 01:11 PM in reply to: KF090

There should be quite a few threads in this forum over the last several years that discuss this problem.  Unfortunately there is no quick fix-- it seems that Inventor can get confused in certain assemblies, and there is no solution other than deleting a bunch of constraints and starting over.  But do some searching and see if there's any more guidance from people with the benefit of experience.

*Expert Elite*
blair
Posts: 3,952
Registered: ‎11-13-2006
Message 4 of 27 (2,109 Views)

Re: Can't move unconstrained parts within an assembly

11-18-2012 03:28 PM in reply to: ben_walker5

Look for a bad constraint, this seems to freeze parts, also having a second part selected in the browser will do the same thing as well.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 up1 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Valued Mentor
stephengibson76
Posts: 1,084
Registered: ‎08-01-2006
Message 5 of 27 (2,100 Views)

Re: Can't move unconstrained parts within an assembly

11-19-2012 01:59 AM in reply to: ben_walker5

do as the others have suggested, but just to get you out of trouble if it needs to go out the door...

 

Although you can not drag the component, you may be able to move it by adding additional constraints, just add them as you would normally would and see if it moves correctly

Stephen Gibson



View stephen gibson's profile on LinkedIn


Employee
t_stramr
Posts: 50
Registered: ‎08-15-2011
Message 6 of 27 (2,061 Views)

Re: Can't move unconstrained parts within an assembly

11-21-2012 05:05 AM in reply to: ben_walker5

Hi Ben,

 

Could you attach your assembly? If you have some simple assembly that exhibits the problem I can take a look closer for source of the problem.

 

Thank you,

Robert

Active Contributor
rjezuit
Posts: 35
Registered: ‎03-09-2011
Message 7 of 27 (2,042 Views)

Re: Can't move unconstrained parts within an assembly

11-21-2012 11:02 AM in reply to: t_stramr

I have had this issue also, in 2010, 2011, and 2012.  It seems to be related to previously placed parts that are grounded. If I "un ground" parts placed before the one that is messed up it seems to free them up. Then I ground the previously un grounded parts. 

Valued Contributor
Barvas11
Posts: 77
Registered: ‎04-15-2010
Message 8 of 27 (1,444 Views)

Re: Can't move unconstrained parts within an assembly

09-10-2013 02:41 AM in reply to: ben_walker5

I have the same problem. And as rjezuit says, try to ungound your parts. Every assembly should have only one part grounded no more than that. Another thing that could be causing this are adaptive sketches and parts. You should always turn the adaptivity off. 

*Expert Elite*
JDMather
Posts: 26,289
Registered: ‎04-20-2006
Message 9 of 27 (1,432 Views)

Re: Can't move unconstrained parts within an assembly

09-10-2013 04:07 AM in reply to: Barvas11

Barvas11 wrote:
.... Every assembly should have only one part grounded no more than that.
...

I often have multiple grounded components (parts or sub-assemblies) within my assemblies.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Valued Contributor
Barvas11
Posts: 77
Registered: ‎04-15-2010
Message 10 of 27 (1,427 Views)

Re: Can't move unconstrained parts within an assembly

09-10-2013 04:54 AM in reply to: JDMather

Well that's what we were told by Autodesk employees. I must say that it makes my life much easier because assemblies with high number of grounded parts don't tent to behave as they should.... 

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube