Inventor General Discussion

Inventor General Discussion

Reply
*Keith_Bradford
Message 11 of 15 (40 Views)

Re:

11-15-2002 02:32 AM in reply to: *Keith_Bradford
Yes I am wondering why it is off by .001.

--
Keith Bradford
CAD Director
SCS/Frigette
817.293.5313
www.scsfrigette.com
(Remove All Numbers From E-mail)
"Mike Maenpaa" wrote in message
news:B86B14AA821E31C9BE4D0E6B57FB30A1@in.WebX.maYIadrTaRb...
> I noticed that too. On one part, the edge selected for the flange is the
> inside edge. On the other part, the outside edge is selected.
> Keith, are you wondering why it's off by .001?
> Mike
>
> "Kent Keller" wrote in message
> news:AF260166F91B6BE666734D85BF88B105@in.WebX.maYIadrTaRb...
> > Keith
> >
*Maenpaa, Mike
Message 12 of 15 (40 Views)

Re:

11-15-2002 02:39 AM in reply to: *Keith_Bradford
Look at Part3 new_reva.ipt, open up the Parameters dialog. The dimension has
.405, but also has a tolerance dim of .4045 for Nominal & Model. I haven't
tried tolerance modeling yet, so I'm not sure how to change that. I think
that's where the .001 is coming from.
Mike

"Keith_Bradford" <7kbradford7@7scsfrigette7.com> wrote in message
news:C82E21031B85769DE62CC4CBD796804E@in.WebX.maYIadrTaRb...
> Yes I am wondering why it is off by .001.
>
> --
> Keith Bradford
> CAD Director
> SCS/Frigette
> 817.293.5313
> www.scsfrigette.com
> (Remove All Numbers From E-mail)
> "Mike Maenpaa" wrote in message
> news:B86B14AA821E31C9BE4D0E6B57FB30A1@in.WebX.maYIadrTaRb...
> > I noticed that too. On one part, the edge selected for the flange is the
> > inside edge. On the other part, the outside edge is selected.
> > Keith, are you wondering why it's off by .001?
> > Mike
> >
> > "Kent Keller" wrote in message
> > news:AF260166F91B6BE666734D85BF88B105@in.WebX.maYIadrTaRb...
> > > Keith
> > >
>
>
*Autodesk\
Message 13 of 15 (40 Views)

Re:

11-15-2002 02:55 AM in reply to: *Keith_Bradford
Flange1 on Part3 new_revA has some problems. On one end of the part, there
is a wire showing where the bend starts. On the other end, the flange is
short. I logged a defect against it.

Loren Jahraus
Autodesk Inventor Workflow Team

"Keith_Bradford" <7kbradford7@7scsfrigette7.com> wrote in message
news:C82E21031B85769DE62CC4CBD796804E@in.WebX.maYIadrTaRb...
> Yes I am wondering why it is off by .001.
>
> --
> Keith Bradford
> CAD Director
> SCS/Frigette
> 817.293.5313
> www.scsfrigette.com
> (Remove All Numbers From E-mail)
> "Mike Maenpaa" wrote in message
> news:B86B14AA821E31C9BE4D0E6B57FB30A1@in.WebX.maYIadrTaRb...
> > I noticed that too. On one part, the edge selected for the flange is the
> > inside edge. On the other part, the outside edge is selected.
> > Keith, are you wondering why it's off by .001?
> > Mike
> >
> > "Kent Keller" wrote in message
> > news:AF260166F91B6BE666734D85BF88B105@in.WebX.maYIadrTaRb...
> > > Keith
> > >
>
>
*Keith_Bradford
Message 14 of 15 (40 Views)

Re:

11-15-2002 02:58 AM in reply to: *Keith_Bradford
Thanks Mike. I repaired it though I am not sure exactly what I did that
solved the problem. In Part 3 per your keen eye, I opened the Parameter and
clicked in the Quation edit box of d2 (0.405) an arrow pops up and I clecked
it and went to Tolerence. Once there I changed the precision to 0. and the
Evaluate Size to Nominal. I saved and updated everything with NO change. I
then opened Part 3 again and Edited Feature on Flange 1 and typed in AGAIN
.405. Updated/Saved again returned to the Assembly and IT WAS CORRECTED.

Thank you for spotting this. I do not think that I would have ever seen it
and I am not sure how I fixed it but it is fixed now.
Is this TRULY OPERATOR error or Software? I can handle either answer being
correct. If it's me....I'll learn. If it's IV it'll be fixed. I would
just like to know which.
--
Keith Bradford
CAD Director
SCS/Frigette
817.293.5313
www.scsfrigette.com
(Remove All Numbers From E-mail)
"Mike Maenpaa" wrote in message
news:FCADD852793B78182CB63A885601F672@in.WebX.maYIadrTaRb...
> Look at Part3 new_reva.ipt, open up the Parameters dialog. The dimension
has
> .405, but also has a tolerance dim of .4045 for Nominal & Model. I haven't
> tried tolerance modeling yet, so I'm not sure how to change that. I think
> that's where the .001 is coming from.
> Mike
>
> "Keith_Bradford" <7kbradford7@7scsfrigette7.com> wrote in message
> news:C82E21031B85769DE62CC4CBD796804E@in.WebX.maYIadrTaRb...
> > Yes I am wondering why it is off by .001.
> >
> > --
> > Keith Bradford
> > CAD Director
> > SCS/Frigette
> > 817.293.5313
> > www.scsfrigette.com
> > (Remove All Numbers From E-mail)
> > "Mike Maenpaa" wrote in message
> > news:B86B14AA821E31C9BE4D0E6B57FB30A1@in.WebX.maYIadrTaRb...
> > > I noticed that too. On one part, the edge selected for the flange is
the
> > > inside edge. On the other part, the outside edge is selected.
> > > Keith, are you wondering why it's off by .001?
> > > Mike
> > >
> > > "Kent Keller" wrote in message
> > > news:AF260166F91B6BE666734D85BF88B105@in.WebX.maYIadrTaRb...
> > > > Keith
> > > >
> >
> >
>
>
*Keith_Bradford
Message 15 of 15 (40 Views)

Re:

11-15-2002 02:59 AM in reply to: *Keith_Bradford
LOL. THANK YOU!

--
Keith Bradford
CAD Director
SCS/Frigette
817.293.5313
www.scsfrigette.com
(Remove All Numbers From E-mail)
"Loren Jahraus (Autodesk)" wrote in message
news:4AB294918F2033FE1410CC443132B6F3@in.WebX.maYIadrTaRb...
> Flange1 on Part3 new_revA has some problems. On one end of the part, there
> is a wire showing where the bend starts. On the other end, the flange is
> short. I logged a defect against it.
>
> Loren Jahraus
> Autodesk Inventor Workflow Team
>
> "Keith_Bradford" <7kbradford7@7scsfrigette7.com> wrote in message
> news:C82E21031B85769DE62CC4CBD796804E@in.WebX.maYIadrTaRb...
> > Yes I am wondering why it is off by .001.
> >
> > --
> > Keith Bradford
> > CAD Director
> > SCS/Frigette
> > 817.293.5313
> > www.scsfrigette.com
> > (Remove All Numbers From E-mail)
> > "Mike Maenpaa" wrote in message
> > news:B86B14AA821E31C9BE4D0E6B57FB30A1@in.WebX.maYIadrTaRb...
> > > I noticed that too. On one part, the edge selected for the flange is
the
> > > inside edge. On the other part, the outside edge is selected.
> > > Keith, are you wondering why it's off by .001?
> > > Mike
> > >
> > > "Kent Keller" wrote in message
> > > news:AF260166F91B6BE666734D85BF88B105@in.WebX.maYIadrTaRb...
> > > > Keith
> > > >
> >
> >
>
>
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.