Installation & Licensing

Reply
Member
brookfield
Posts: 3
Registered: ‎08-22-2013
Message 1 of 6 (303 Views)

Deploying via MSI / MST partially installs Inventor 2014

303 Views, 5 Replies
08-22-2013 12:22 PM

I have recently created a new deployment package for Inventor Professional 2014. I initially tried to deploy this via group policy using the msi and mst files from the deployment per the install guide. I initially tested deployment via group policy on 5 machines. The msi did run on these machines and created an icon oin the desktop for inventor pro. However, when I click the new icon on the desktop, I just get a quick spinner icon on the mouse and the program never opens. I have tried using various users with and without local admin previleges. 

 

So then I tested deploying on a few machines by setting up the deployment on a globally accessible share and running the master lnk. This installs Inventor as well as 4 other Autodesk products on the desktop and everything works normally. At this point it is easier to just deploy this way than to try to identify the problem with the msi install. 

 

My problem now is that I can not get the software to install on the machines that have run the msi installer from group policy. I have tried to manually install via the .lnk, over top of the msi install. This does not install anything additional and INventor still does not work. I have also tried manually uninstalling all Autodesk software, the running the .lnk install again. Same result, the icon on the desktop and the shortcut in start menu does not open the application. 

 

So now my 5 deployment pilot machines are stuck and I can not get the software to install. Please advise how I could get these back to a fresh install state and just run the .lnk based install. 

 

Any assistance you can provide is greatly appreciated!

Thanks,

 

Dave Stewart

*Expert Elite*
TravisNave
Posts: 10,064
Registered: ‎01-14-2005
Message 2 of 6 (301 Views)

Re: Deploying via MSI / MST partially installs Inventor 2014

08-22-2013 12:28 PM in reply to: brookfield

Welcome to the community. 

 

To Diagnose and Fix installation problems automatically, please see the new Microsoft tool for this here:

http://support.microsoft.com/mats/Program_Install_and_Uninstall

For more information on the Autodesk KB Support article concerning the clean uninstall of Autodesk products, see this link:

http://usa.autodesk.com/adsk/servlet/ps/dl/item?siteID=123112&id=2887771&linkID=9240617

That should get you started. 

 

Good Luck!

Travis Nave Send TravisNave a Private Message                       Need help in your post? Mention me with @TravisNave
Member
brookfield
Posts: 3
Registered: ‎08-22-2013
Message 3 of 6 (279 Views)

Re: Deploying via MSI / MST partially installs Inventor 2014

08-23-2013 12:25 PM in reply to: TravisNave

I have done everything in the links provided, but it still will not install Inventro Pro 2014 properly. I even found a few more registry keys and tried removing those on a test machine. No dice. 

 

I also found that there is an Autodesk Inventor Simulation service that is installed and orphaned upon uninstall. I have manually disabled this on the last few attempts (before uninstall and reinstall). I think there is a reportable bug here in the 2014 installer system. 

 

Please let me know the best way to proceed. I have to get these machines working before classes start 10 days from now. 

Thanks,

Dave

*Expert Elite*
TravisNave
Posts: 10,064
Registered: ‎01-14-2005
Message 4 of 6 (274 Views)

Re: Deploying via MSI / MST partially installs Inventor 2014

08-23-2013 01:33 PM in reply to: brookfield

If you are desperate, you can try this:

http://forums.autodesk.com/t5/Installation-Licensing/Microsoft-Installer-Clean-Up-Utility-for-Add-Re...

 

But you will more than likely have a registry error on reinstall.  You can fix it though from the additional instructions in my link.  Use at your own risk.

Travis Nave Send TravisNave a Private Message                       Need help in your post? Mention me with @TravisNave
Member
brookfield
Posts: 3
Registered: ‎08-22-2013
Message 5 of 6 (223 Views)

Re: Deploying via MSI / MST partially installs Inventor 2014

09-09-2013 03:24 PM in reply to: TravisNave

I have tried your suggested method amd just about everything else possible. I can not get Inventor to install on any of the problem machines. I need to get this resolved and the applications working on all pcs for the class/students. Please advise how we can get or purchase support to get someone to look into this issue. 

*Expert Elite*
TravisNave
Posts: 10,064
Registered: ‎01-14-2005
Message 6 of 6 (193 Views)

Re: Deploying via MSI / MST partially installs Inventor 2014

09-13-2013 08:07 AM in reply to: brookfield

What is the exact problem that is happening then? 

 

You can probably purchase support from your Reseller.

Travis Nave Send TravisNave a Private Message                       Need help in your post? Mention me with @TravisNave

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Up & Ready Blog

Boldly Install, Configure and Deploy Autodesk Software.

AutodeskHelp Blog

Your one-stop shop for the latest solutions, breaking news, and behind the scenes access to the world of Autodesk support.

Connect with Us

Twitter

Pinterest

Blog

Youtube