Installation & Licensing

*Howerton, Richard
Message 1 of 2 (83 Views)

Can't load ADLM!

83 Views, 1 Replies
12-02-1999 08:26 AM
We have upgraded to Netware 5 now. Running both IP and IPX.
Now when I try to load the adlm (ipx), I get the following error on server

CreateProperty error: 255 NetwareErrno: 0
99-DEC-02 08:37:44: CreateProperty failed for: ad_elmdPEHLEXF)!
. ADSKELMD>NLM Terminated.

See attached bmp.
What now?

thanks in advance..

Jerry Milana [Autodesk] wrote in message
> Richard,
> Bud was the person I was going to ask, so you got your answer sooner. I
> want to caution you that when running a configuration that we have not
> tested I am limited in support resources. If you wish to try, here are a
> few ideas:
> Make sure that IPX protocol is the primary protocol on your workstations.
> Your NetWare server must have only one network adapter in it. Lock the
> adapter down to a single speed.
> Remember to set the ACADSERVER variable on your workstations.
> If you are routing IPX, AdLM uses SAP address 2064.
> If you decide to try this and run into trouble, post a message here, Bud
> I will do our best to help. If it works, please let us know too..
> jerry
> Bud Schroeder wrote in message <>...
> >Hi Jerry and Richard,
> >
> >When the LAB Manager setup the 5x server, he only setup IPX. He talked
> about doing
> >both IP and IPX, but never got around to it. At this point, I can only
> to give
> >it a try.
> >
> >Thanks
> >
> >Bud
> >
> >jerry milana [Autodesk] wrote:
> >
> >> Richard,
> >>
> >> I know that AdLM will run on a Netware 5 server running IPX protocol.
> do not
> >> know if we have tested it with servers using both protocols active. I
> will
> >> check for you and post the information on this forum. It may be next
> week
> >> before I know and as I am on Jury duty next week as well, it may be
> Tuesday
> >> evening before I can post the answer.
> >>
> >> Jerry Milana,
> >> Autodesk Product Support
> >>
> >> Richard Howerton wrote:
> >>
> >> > I have the ADLM running on IPX on my Netware 4.11 server. We are
> upgrading
> >> > to Netware 5. Will the ipx ADLM run on it ok? In co-existence with
> (Not
> >> > the IP ADLM)
> >
> >
> >

Message 2 of 2 (83 Views)

Re: Can't load ADLM!

02-01-2000 11:20 AM in reply to: *Howerton, Richard

We get a similar problem:
CreateProperty error:237 Netware: 0 failed for: ad_elmdSI ADSKELMD.NLM
It appears to load correctly manually but not automatically when we re-boot
the server.

I believe this may be the cause of our drawing locking problem. We have
users x-ref'ing drawings which lock out other users from making saves.
eg. If UserA has A.DWG opened with XREF.DWG attached, UserB can't save
B.DWG which also references XREF.DWG. I have to have UserA exit AutoCAD
before UserB can save B.DWG.

Maybe someone can see a correlation.

** ** ** * ** * ****** * * * * * * * * * * * * * * *

Richard Howerton wrote in message
> We have upgraded to Netware 5 now. Running both IP and IPX.
> Now when I try to load the adlm (ipx), I get the following ...

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community

Up & Ready Blog

Boldly Install, Configure and Deploy Autodesk Software.

AutodeskHelp Blog

Your one-stop shop for the latest solutions, breaking news, and behind the scenes access to the world of Autodesk support.

Connect with Us