Autodesk Survey Products

[#1]

HEY ALL, I NEED HELP!
when I export a points file from terramodel convert it to a .fbk file using the survey link dc 7.5.5; this is the out put I get after the conversion.

ASCII

1349,356567.61,13454014.08,649.59,B 5531
1350,356568.93,13454014.69,649.62,MCS 5531
1351,356572.31,13454016.15,649.61,5531
1352,356576.07,13454018.65,649.45,5531
1353,356576.77,13454020.03,649.39,5531
1354,356577.71,13454022.46,649.33,5531
1355,356577.71,13454024.34,649.32,MCE 5531
1356,356577.92,13454030.03,649.28,E 5531

CONVERTED .FBK

BEG 5531
NE SS 1349 356567.61000 13454014.08000 649.59000 "5531"
END
NE SS 1350 356568.93000 13454014.69000 649.62000 "MCS 5531"
END
NE SS 1351 356572.31000 13454016.15000 649.61000 "5531"
NE SS 1352 356576.07000 13454018.65000 649.45000 "5531"
NE SS 1353 356576.77000 13454020.03000 649.39000 "5531"
NE SS 1354 356577.71000 13454022.46000 649.33000 "5531"
END
NE SS 1355 356577.71000 13454024.34000 649.32000 "MCE 5531"
END

"5531" IS MY FIELD CODE FOR CURB LINE 1; I THINK THE MCS SHOULD BE ON THE LINE ABOVE AND NOT SHOWING WHERE IT'S SHOWN ABOVE... ALSO, WHEN I IMPORT THE ABOVE FBK FILE TO AUTOCAD CIVIL 3D 2009..NO CURVE.

HELP! MY BRAIN HURTS!!
THANKS
JOE

[#2]

Hi joe,

The field book should be something like. Note I haven't tested this and
the MCE should possibly be one line later in the file

BEG 5531
NE SS 1349 356567.61000 13454014.08000 649.59000 "5531"
MCS
NE SS 1350 356568.93000 13454014.69000 649.62000 "5531"
NE SS 1351 356572.31000 13454016.15000 649.61000 "5531"
NE SS 1352 356576.07000 13454018.65000 649.45000 "5531"
NE SS 1353 356576.77000 13454020.03000 649.39000 "5531"
NE SS 1354 356577.71000 13454022.46000 649.33000 "5531"
MCE
NE SS 1355 356577.71000 13454024.34000 649.32000 "5531"
END // Only needed if next point is not on the figure



Regards,


Laurie Comerford


joegayeski6344 wrote:
> HEY ALL, I NEED HELP!
> when I export a points file from terramodel convert it to a .fbk file using the survey link dc 7.5.5; this is the out put I get after the conversion.
>
> ASCII
>
> 1349,356567.61,13454014.08,649.59,B 5531
> 1350,356568.93,13454014.69,649.62,MCS 5531
> 1351,356572.31,13454016.15,649.61,5531
> 1352,356576.07,13454018.65,649.45,5531
> 1353,356576.77,13454020.03,649.39,5531
> 1354,356577.71,13454022.46,649.33,5531
> 1355,356577.71,13454024.34,649.32,MCE 5531
> 1356,356577.92,13454030.03,649.28,E 5531
>
> CONVERTED .FBK
>
> BEG 5531
> NE SS 1349 356567.61000 13454014.08000 649.59000 "5531"
> END
> NE SS 1350 356568.93000 13454014.69000 649.62000 "MCS 5531"
> END
> NE SS 1351 356572.31000 13454016.15000 649.61000 "5531"
> NE SS 1352 356576.07000 13454018.65000 649.45000 "5531"
> NE SS 1353 356576.77000 13454020.03000 649.39000 "5531"
> NE SS 1354 356577.71000 13454022.46000 649.33000 "5531"
> END
> NE SS 1355 356577.71000 13454024.34000 649.32000 "MCE 5531"
> END
>
> "5531" IS MY FIELD CODE FOR CURB LINE 1; I THINK THE MCS SHOULD BE ON THE LINE ABOVE AND NOT SHOWING WHERE IT'S SHOWN ABOVE... ALSO, WHEN I IMPORT THE ABOVE FBK FILE TO AUTOCAD CIVIL 3D 2009..NO CURVE.
>
> HELP! MY BRAIN HURTS!!
> THANKS
> JOE
>