Spread Sheet Calculator

[Anonymous]

When I open spreadsheet calculator in version 2012, it only comes up as a Demo Version.

When i open it in 2013, only the excel page opens, with no libraries, etc. There is nothing prompting me to select an analysis.

Do I need to do  separate registration to use the Spreadsheet Calculator?

[Anonymous]

When I open spreadsheet calculator in version 2012, it only comes up as a Demo Version.

When i open it in 2013, only the excel page opens, with no libraries, etc. There is nothing prompting me to select an analysis.

Do I need to do  separate registration to use the Spreadsheet Calculator?

[StefanoPasquini6790]

Good morning,

try to run as administrator all the ESOP app in the folder: 

C:\Program Files\Autodesk\Autodesk Robot Structural Analysis Professional 2013\RESC

[StefanoPasquini6790]

Good morning,

try to run as administrator all the ESOP app in the folder: 

C:\Program Files\Autodesk\Autodesk Robot Structural Analysis Professional 2013\RESC

[Rafal.Gaweda]

---

LLAL wrote:

When I open spreadsheet calculator in version 2012, it only comes up as a Demo Version.

When i open it in 2013, only the excel page opens, with no libraries, etc. There is nothing prompting me to select an analysis.

For 2013:

- Install SC Content if not installed

- copy files from attached zips to correct SC folders.

[Rafal.Gaweda]

---

LLAL wrote:

When I open spreadsheet calculator in version 2012, it only comes up as a Demo Version.

When i open it in 2013, only the excel page opens, with no libraries, etc. There is nothing prompting me to select an analysis.

For 2013:

- Install SC Content if not installed

- copy files from attached zips to correct SC folders.

[StefanoPasquini6790]

Hi everyone,

I can't use the libaries in Spreadsheet Calculator for Robot Structural Analysis 2014, as you can see in the following picture: 

I've downloaded and installed the spreadsheet for 2014.

Attached on this mail the diagnosis report of the ESOP Start. What can I do to fix this issue?

Greetings at all.

[StefanoPasquini6790]

Hi everyone,

I can't use the libaries in Spreadsheet Calculator for Robot Structural Analysis 2014, as you can see in the following picture: 

I've downloaded and installed the spreadsheet for 2014.

Attached on this mail the diagnosis report of the ESOP Start. What can I do to fix this issue?

Greetings at all.

[Rafal.Gaweda]

Which office do you have? 32 or 64 bit?
Have you downloaded and installed SC 2014 Content ?

[Rafal.Gaweda]

Which office do you have? 32 or 64 bit?
Have you downloaded and installed SC 2014 Content ?

[StefanoPasquini6790]

Good morning Rafal,

I've downloaded the and installed SC 2014 content in this folder: 

C:\Program Files\Autodesk\Autodesk Robot Structural Analysis Professional 2014\RESC\Engineering\lib

I have Office 2007 with this info capture:

I don't know if it's 32 or 64 bit. How can I check this, the software was pre installed on PC when I purchase it.

Greetings

[StefanoPasquini6790]

Good morning Rafal,

I've downloaded the and installed SC 2014 content in this folder: 

C:\Program Files\Autodesk\Autodesk Robot Structural Analysis Professional 2014\RESC\Engineering\lib

I have Office 2007 with this info capture:

I don't know if it's 32 or 64 bit. How can I check this, the software was pre installed on PC when I purchase it.

Greetings

[Tuctas]

  I recently made a format in my PC so i had to re-install ARSA2013, but i face the same problem with SC as described above, i.e with no libraries (actually it isn't the 1st time that happens to me, as far as i remember i hade the same problem many times in the past..). I did the "usual" procudure of unregistering- registering the componets (see attached) but it dididn't work. I am not sure if i did it well as the last time i did it was 1-2 years, so which components should we unregister and then register?  

[Tuctas]

  I recently made a format in my PC so i had to re-install ARSA2013, but i face the same problem with SC as described above, i.e with no libraries (actually it isn't the 1st time that happens to me, as far as i remember i hade the same problem many times in the past..). I did the "usual" procudure of unregistering- registering the componets (see attached) but it dididn't work. I am not sure if i did it well as the last time i did it was 1-2 years, so which components should we unregister and then register?  

[Rafal.Gaweda]

Have you downloaded and installed SC content ?

[Rafal.Gaweda]

Have you downloaded and installed SC content ?

[Tuctas]

It is included in the CD, isn't it?. The existence of RESC file doesn't proove that?

[Tuctas]

It is included in the CD, isn't it?. The existence of RESC file doesn't proove that?

[Rafal.Gaweda]

No, on subscription.

[Rafal.Gaweda]

No, on subscription.

[Tuctas]

When version ARSA2013 came out for the first time, i was subscribed but now  i am not. Do you mean that now that i am just reinstalling ASRSA2013 i am not able to use SC..!? That's not fair at all...

[Tuctas]

When version ARSA2013 came out for the first time, i was subscribed but now  i am not. Do you mean that now that i am just reinstalling ASRSA2013 i am not able to use SC..!? That's not fair at all...

[Tuctas]

Never mind, i fixed it... I played with the unregister-register procedure and then opend the 5 Esop files as administrator and it was o.k...

[Tuctas]

Never mind, i fixed it... I played with the unregister-register procedure and then opend the 5 Esop files as administrator and it was o.k...

[matracprojects4]

Kindly put through for the meaning of the following denotations for internal forces in Robot structural calculation sheet.

N,Ed 

Nc,Rd 

Nb,Rd 

Thanks in anticipation of your feedback. 

[matracprojects4]

Kindly put through for the meaning of the following denotations for internal forces in Robot structural calculation sheet.

N,Ed 

Nc,Rd 

Nb,Rd 

Thanks in anticipation of your feedback.