Autodesk Inventor
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
*Johnson, Bob
Sheetmetal holes?
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
39 Views, 3 Replies
12-10-2002 02:15 PM
Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
selected at the same time and with the same diameter. How can I change the
diameter of only one of the holes? TIA, Bob
selected at the same time and with the same diameter. How can I change the
diameter of only one of the holes? TIA, Bob
*Keller, Kent
Re: Sheetmetal holes?
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-10-2002 03:04 PM in reply to:
*Johnson, Bob
Rmb on the hole in the browser, and edit. Hold the control key and select
the one you want different to remove it from the rest that are selected. Ok
to finish the edit, then rmb on the sketch in the browser for the holes and
share it. Now add another hole using the point that you removed from the
other hole set.
--
Kent Keller
Member of the Autodesk Discussion Forum Moderator Program
http://www.MyMcad.com/KWiK/Mcad.htm
"Bob Johnson" wrote in message
news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYI
> Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
> selected at the same time and with the same diameter. How can I change the
> diameter of only one of the holes? TIA, Bob
>
>
the one you want different to remove it from the rest that are selected. Ok
to finish the edit, then rmb on the sketch in the browser for the holes and
share it. Now add another hole using the point that you removed from the
other hole set.
--
Kent Keller
Member of the Autodesk Discussion Forum Moderator Program
http://www.MyMcad.com/KWiK/Mcad.htm
"Bob Johnson"
news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYI
> Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern, all
> selected at the same time and with the same diameter. How can I change the
> diameter of only one of the holes? TIA, Bob
>
>
*Johnson, Bob
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-11-2002 01:43 AM in reply to:
*Johnson, Bob
Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
key/select hole center point/OK, select hole tool, enter new hole size/OK?
Thanks again, Bob
"Kent Keller" wrote in message
news:88CEF94E0ADD9B27E6DFB81B296523DC@in.WebX.maYI
> Rmb on the hole in the browser, and edit. Hold the control key and select
> the one you want different to remove it from the rest that are selected.
Ok
> to finish the edit, then rmb on the sketch in the browser for the holes
and
> share it. Now add another hole using the point that you removed from the
> other hole set.
> --
> Kent Keller
> Member of the Autodesk Discussion Forum Moderator Program
>
> http://www.MyMcad.com/KWiK/Mcad.htm
>
> "Bob Johnson" wrote in message
> news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYI
> > Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern,
all
> > selected at the same time and with the same diameter. How can I change
the
> > diameter of only one of the holes? TIA, Bob
> >
> >
>
>
key/select hole center point/OK, select hole tool, enter new hole size/OK?
Thanks again, Bob
"Kent Keller"
news:88CEF94E0ADD9B27E6DFB81B296523DC@in.WebX.maYI
> Rmb on the hole in the browser, and edit. Hold the control key and select
> the one you want different to remove it from the rest that are selected.
Ok
> to finish the edit, then rmb on the sketch in the browser for the holes
and
> share it. Now add another hole using the point that you removed from the
> other hole set.
> --
> Kent Keller
> Member of the Autodesk Discussion Forum Moderator Program
>
> http://www.MyMcad.com/KWiK/Mcad.htm
>
> "Bob Johnson"
> news:B32208D7A81F1BD4B66998F409C510C0@in.WebX.maYI
> > Hi all, I have a sheetmetal panel. The panel has 4 holes in a pattern,
all
> > selected at the same time and with the same diameter. How can I change
the
> > diameter of only one of the holes? TIA, Bob
> >
> >
>
>
*Keller, Kent
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-11-2002 02:05 AM in reply to:
*Johnson, Bob
Not if I am following correctly (always suspect that I am not)
AFAIK you can not have two hole sizes on a sketch unless the sketch is shared. It sounds
to me like that is what you are trying to do. If you just share the sketch then
everything will be happy.
--
Kent
Member of the Autodesk Discussion Forum Moderator Program
"Bob Johnson" wrote in message
news:E607262317971A6A1E0E5AD969846BA2@in.WebX.maYI
> Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
> key/select hole center point/OK, select hole tool, enter new hole size/OK?
> Thanks again, Bob
AFAIK you can not have two hole sizes on a sketch unless the sketch is shared. It sounds
to me like that is what you are trying to do. If you just share the sketch then
everything will be happy.
--
Kent
Member of the Autodesk Discussion Forum Moderator Program
"Bob Johnson"
news:E607262317971A6A1E0E5AD969846BA2@in.WebX.maYI
> Kent, will this also work, RMB on hole in browser, select edit feature, ctrl
> key/select hole center point/OK, select hole tool, enter new hole size/OK?
> Thanks again, Bob
