Autodesk Inventor
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
Inventor 5 wont open!!!
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
68 Views, 3 Replies
12-02-2006 11:07 AM
So i recently tried to load Inventor 5 onto my home computer. The installation went fine, but now the welcome image opens (a spaceship) for a couple seconds, disappears, and then nothing else happens. any help would be great!
*Duncan Anderson
Re: Inventor 5 wont open!!!
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-04-2006 04:31 AM in reply to:
mattman_83
It's a very deep sub-mersible
Inv should go to the Activation/Registration screen after the initial splash screen.
Did you disable your anti-virus when installing ?
Do you have Flash8(a) installed - remove using the utility from
http://www.adobe.com/cfusion/knowledgebase/index.c
And then install Flash9 http://www.adobe.com/go/getflashplayer
--
Duncan
"Humour ... is one man shouting gibberish in the face of authority, and proving by
fabricated insanity that nothing could be as mad as what passes for ordinary
living."
(Terence 'Spike' Milligan K.B.E., 1918-2002)
www.autodesk.co.uk/inventorjobs
wrote in message news:5412885@discussion.autodesk.com...
So i recently tried to load Inventor 5 onto my home computer. The installation went
fine, but now the welcome image opens (a spaceship) for a couple seconds,
disappears, and then nothing else happens. any help would be great!
Inv should go to the Activation/Registration screen after the initial splash screen.
Did you disable your anti-virus when installing ?
Do you have Flash8(a) installed - remove using the utility from
http://www.adobe.com/cfusion/knowledgebase/index.c
And then install Flash9 http://www.adobe.com/go/getflashplayer
--
Duncan
"Humour ... is one man shouting gibberish in the face of authority, and proving by
fabricated insanity that nothing could be as mad as what passes for ordinary
living."
(Terence 'Spike' Milligan K.B.E., 1918-2002)
www.autodesk.co.uk/inventorjobs
So i recently tried to load Inventor 5 onto my home computer. The installation went
fine, but now the welcome image opens (a spaceship) for a couple seconds,
disappears, and then nothing else happens. any help would be great!
*Joe Howard
Re: Inventor 5 wont open!!!
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-04-2006 05:09 AM in reply to:
mattman_83
Do you have Excell on your home machine? it is required for inventor and if
just installed excell you must open excell at least once to activate it.
wrote in message news:5412885@discussion.autodesk.com...
So i recently tried to load Inventor 5 onto my home computer. The
installation went fine, but now the welcome image opens (a spaceship) for a
couple seconds, disappears, and then nothing else happens. any help would
be great!
just installed excell you must open excell at least once to activate it.
So i recently tried to load Inventor 5 onto my home computer. The
installation went fine, but now the welcome image opens (a spaceship) for a
couple seconds, disappears, and then nothing else happens. any help would
be great!
*Gary R Smith \(Autodesk\)
Re: Inventor 5 wont open!!!
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-04-2006 06:45 AM in reply to:
mattman_83
You might also make sure that your home machine has a graphics card/drivers
that supported INV5
that supported INV5
