Autodesk Inventor
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
*Myers, Kim
IV6 Sketch Dimension Error
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
14 Views, 3 Replies
12-09-2002 12:05 AM
Please take a look at the file under the same topic in CF. The value of my
sketch dimension is not correct in regards to the actual value. I have no
idea how this happened. Has anyone else seen this?
sketch dimension is not correct in regards to the actual value. I have no
idea how this happened. Has anyone else seen this?
Re: IV6 Sketch Dimension Error
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-09-2002 12:24 AM in reply to:
*Myers, Kim
i haven't looked at your post, but today in idw mode, i got a dimension that was 2.13". i knew that wasn't correct. exited the idw, opened it again, and dimmed again. it then gave me the correct dimension of 7.36". go figure? -Joe
*Myers, Kim
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-09-2002 12:52 AM in reply to:
*Myers, Kim
This was in a .ipt, but yours is just as bad if not
worse. The guys in the shop just love to hear it when we blame our
mistakes on the software. The problem is they think it is just an
excuse.
worse. The guys in the shop just love to hear it when we blame our
mistakes on the software. The problem is they think it is just an
excuse.
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"jmartzig" <haven't
href="mailto:j.martzig@rofin-inc.com">j.martzig@rofin-inc.com> wrote in
message
href="news:f12ae8c.0@WebX.maYIadrTaRb">news:f12ae8c.0@WebX.maYIadrTaRb...
looked at your post, but today in idw mode, i got a dimension that was 2.13".
i knew that wasn't correct. exited the idw, opened it again, and dimmed again.
it then gave me the correct dimension of 7.36". go figure?
-Joe
*Myers, Kim
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
12-10-2002 05:23 AM in reply to:
*Myers, Kim
Anyone have any thoughts on this?
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"Kim Myers" <---> wrote in message
href="news:9785BCD804BDF395CF027E4151FA8163@in.WebX.maYIadrTaRb">news:9785BCD804BDF395CF027E4151F......
This was in a .ipt, but yours is just as bad if
not worse. The guys in the shop just love to hear it when we blame our
mistakes on the software. The problem is they think it is just an
excuse.
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"jmartzig" <haven't
href="mailto:j.martzig@rofin-inc.com">j.martzig@rofin-inc.com> wrote
in message
href="news:f12ae8c.0@WebX.maYIadrTaRb">news:f12ae8c.0@WebX.maYIadrTaRb...
looked at your post, but today in idw mode, i got a dimension that was
2.13". i knew that wasn't correct. exited the idw, opened it again, and
dimmed again. it then gave me the correct dimension of 7.36". go figure?
-Joe
