Autodesk Inventor
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
*Koch, Erich
Hatch dimensions
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
29 Views, 2 Replies
11-26-2002 02:02 AM
Hello Group.
We are having problems with dimensioning hatch areas.
We want to draw a rectangle so paint is no applied there. We can dimension the
rectangle but not against the part itself. Dims does not recognized the part,
does not see it!!
We have no problem doing this with 5.3. I made sure we are on the right view
when we went to sketch mode to draw the rectangle and then the hatch.
Any suggestions?
Thanks,
Erich
We are having problems with dimensioning hatch areas.
We want to draw a rectangle so paint is no applied there. We can dimension the
rectangle but not against the part itself. Dims does not recognized the part,
does not see it!!
We have no problem doing this with 5.3. I made sure we are on the right view
when we went to sketch mode to draw the rectangle and then the hatch.
Any suggestions?
Thanks,
Erich
*Ryan, John
Re: Hatch dimensions
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
11-26-2002 02:11 AM in reply to:
*Koch, Erich
There is an option under Tools /Application Options/ Sketch "Autoproject
edges during curve creation" that you need to check so you can reference the
drawing entities while you sketch in the view. The other way to do this is
to project geometry (one of the sketch tools in the toolbar) and this will
allow you to reference to the geometry in the view.
"Erich Koch" wrote in message
news:3DE3B726.14248475@aerovironment.com...
> Hello Group.
>
> We are having problems with dimensioning hatch areas.
>
> We want to draw a rectangle so paint is no applied there. We can dimension
the
> rectangle but not against the part itself. Dims does not recognized the
part,
> does not see it!!
> We have no problem doing this with 5.3. I made sure we are on the right
view
> when we went to sketch mode to draw the rectangle and then the hatch.
> Any suggestions?
>
> Thanks,
> Erich
>
edges during curve creation" that you need to check so you can reference the
drawing entities while you sketch in the view. The other way to do this is
to project geometry (one of the sketch tools in the toolbar) and this will
allow you to reference to the geometry in the view.
"Erich Koch"
news:3DE3B726.14248475@aerovironment.com...
> Hello Group.
>
> We are having problems with dimensioning hatch areas.
>
> We want to draw a rectangle so paint is no applied there. We can dimension
the
> rectangle but not against the part itself. Dims does not recognized the
part,
> does not see it!!
> We have no problem doing this with 5.3. I made sure we are on the right
view
> when we went to sketch mode to draw the rectangle and then the hatch.
> Any suggestions?
>
> Thanks,
> Erich
>
*Koch, Erich
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
11-26-2002 02:16 AM in reply to:
*Koch, Erich
THANK YOU,
Erich
John Ryan wrote:
> There is an option under Tools /Application Options/ Sketch "Autoproject
> edges during curve creation" that you need to check so you can reference the
> drawing entities while you sketch in the view. The other way to do this is
> to project geometry (one of the sketch tools in the toolbar) and this will
> allow you to reference to the geometry in the view.
Erich
John Ryan wrote:
> There is an option under Tools /Application Options/ Sketch "Autoproject
> edges during curve creation" that you need to check so you can reference the
> drawing entities while you sketch in the view. The other way to do this is
> to project geometry (one of the sketch tools in the toolbar) and this will
> allow you to reference to the geometry in the view.
