Autodesk Inventor
I'm probably not interpreting what you are doing correctly, but I patterned
some radial lines, made an ellipse on one and trimmed it. Offset a couple of
workplanes and projected successive lines to them drawing and trimming the
ellipses and didn't see any errors. If you want to post what it is you're
trying to do exactly, I could see what I misunderstood.
~Larry
"Jeff Howard" wrote in message
news
F055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
some radial lines, made an ellipse on one and trimmed it. Offset a couple of
workplanes and projected successive lines to them drawing and trimming the
ellipses and didn't see any errors. If you want to post what it is you're
trying to do exactly, I could see what I misunderstood.
~Larry
"Jeff Howard"
news
F055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
Oh ... it was already there. I didn't get the same result. Mine trimmed
okay. See CF.
~Larry
"Jeff Howard" wrote in message
newsF055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
okay. See CF.
~Larry
"Jeff Howard"
news
F055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
I opened your file in the RTM build, and the ellipse segment was green.
Loren Jahraus
Autodesk Inventor Workflow Team
"Jeff Howard" wrote in message
newsF055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR
> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
Loren Jahraus
Autodesk Inventor Workflow Team
"Jeff Howard"
news
F055279A9F459D8BB68F5FC4C198765@in.WebX.maYIadrTaR> File in CF.
>
> What I'm trying to do is set up a sketch with ellipse and radial lines for
> projection to new sketches which will be elliptical segments. The radials
are
> projected, an ellipse sketched using the radials and then trimmed. When
> trimmed the ellipse segment goes red (can't solve constraints?).
>
> Thanks,
> Jeff
> =============================
>
>
