Autodesk Inventor
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
Crashing Inventor 5.3
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
29 Views, 1 Replies
11-10-2002 08:28 AM
Every time I try to create a flat pattern from a sheet metal part I get the following illegal operations:
INVENTOR caused an invalid page fault in
module ATIO9XAA.DLL at 0177:69132be6.
Registers:
EAX=06e3000c CS=0177 EIP=69132be6 EFLGS=00010206
EBX=00000000 SS=017f ESP=00d9f650 EBP=05e3749c
ECX=00000000 DS=017f ESI=05e3749c FS=4447
EDX=05e3749c ES=017f EDI=05e37420 GS=0000
Bytes at CS:EIP:
ff 51 60 85 c0 0f 95 c0 c3 90 53 56 8b f1 8b 86
Stack dump:
06e3000c 69131684 05e37420 00000000 691316b3 00d9f6fc 05e37420 05e3749c 00000000 691318b9 00d9f6fc 4b488b88 00000000 00000000 69131a5c 00d9f6fc
INVENTOR caused an invalid page fault in
module KERNEL32.DLL at 0177:bff9db61.
Registers:
EAX=c00309c4 CS=0177 EIP=bff9db61 EFLGS=00010212
EBX=0541fe28 SS=017f ESP=0531ff68 EBP=05320204
ECX=00000000 DS=017f ESI=00000000 FS=653f
EDX=bff76855 ES=017f EDI=bff79198 GS=0000
Bytes at CS:EIP:
53 8b 15 e4 9c fc bf 56 89 4d e4 57 89 4d dc 89
Stack dump:
My graphics card is an ATI 128 xpert.
Does anyone know how to get around this?
INVENTOR caused an invalid page fault in
module ATIO9XAA.DLL at 0177:69132be6.
Registers:
EAX=06e3000c CS=0177 EIP=69132be6 EFLGS=00010206
EBX=00000000 SS=017f ESP=00d9f650 EBP=05e3749c
ECX=00000000 DS=017f ESI=05e3749c FS=4447
EDX=05e3749c ES=017f EDI=05e37420 GS=0000
Bytes at CS:EIP:
ff 51 60 85 c0 0f 95 c0 c3 90 53 56 8b f1 8b 86
Stack dump:
06e3000c 69131684 05e37420 00000000 691316b3 00d9f6fc 05e37420 05e3749c 00000000 691318b9 00d9f6fc 4b488b88 00000000 00000000 69131a5c 00d9f6fc
INVENTOR caused an invalid page fault in
module KERNEL32.DLL at 0177:bff9db61.
Registers:
EAX=c00309c4 CS=0177 EIP=bff9db61 EFLGS=00010212
EBX=0541fe28 SS=017f ESP=0531ff68 EBP=05320204
ECX=00000000 DS=017f ESI=00000000 FS=653f
EDX=bff76855 ES=017f EDI=bff79198 GS=0000
Bytes at CS:EIP:
53 8b 15 e4 9c fc bf 56 89 4d e4 57 89 4d dc 89
Stack dump:
My graphics card is an ATI 128 xpert.
Does anyone know how to get around this?
*darvinv
Re: Crashing Inventor 5.3
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
11-10-2002 09:50 AM in reply to:
alfie_smith10
Suggest you goto this link. As far as I know, if a
card/driver combo is not showing a green dot on this page, it is probably not
reliable in inventor! You may get some work out of it, but sooner or later you
hit a wall. Seen that ATI*****.dll in a lot of stack dumps.
card/driver combo is not showing a green dot on this page, it is probably not
reliable in inventor! You may get some work out of it, but sooner or later you
hit a wall. Seen that ATI*****.dll in a lot of stack dumps.
darvin
