Autodesk Freewheel
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
transparen
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
67 Views, 2 Replies
07-17-2007 08:58 AM
I am trying to upload an assembly includes a cylinder that I have extruded in Inventor. The surface of this cylinder is Polycarbonate (clear), so the parts inside it may be visible. When I save this assembly as a .dwf file and view it with Autodesk Design Review, I am able to view the clear surface and everything inside it perfectly. However, when I open it with Autodesk Freewheel, only 1/4 of the transparent cylinder shows up. Any ideas? Thanks.
*Scott Sheppard - Autodesk
Re: transparen
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
07-17-2007 01:14 PM in reply to:
mattd7
Please provide the DWF as a test case.
wrote in message news:5660266@discussion.autodesk.com...
I am trying to upload an assembly includes a cylinder that I have extruded
in Inventor. The surface of this cylinder is Polycarbonate (clear), so the
parts inside it may be visible. When I save this assembly as a .dwf file
and view it with Autodesk Design Review, I am able to view the clear surface
and everything inside it perfectly. However, when I open it with Autodesk
Freewheel, only 1/4 of the transparent cylinder shows up. Any ideas?
Thanks.
I am trying to upload an assembly includes a cylinder that I have extruded
in Inventor. The surface of this cylinder is Polycarbonate (clear), so the
parts inside it may be visible. When I save this assembly as a .dwf file
and view it with Autodesk Design Review, I am able to view the clear surface
and everything inside it perfectly. However, when I open it with Autodesk
Freewheel, only 1/4 of the transparent cylinder shows up. Any ideas?
Thanks.
*Gyuri Ordody [Autodesk]
Re: transparen
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
08-27-2007 11:13 AM in reply to:
mattd7
No need to upload, I have reproduced the problem.
Gyuri
Scott Sheppard - Autodesk wrote:
> Please provide the DWF as a test case.
>
> wrote in message news:5660266@discussion.autodesk.com...
> I am trying to upload an assembly includes a cylinder that I have extruded
> in Inventor. The surface of this cylinder is Polycarbonate (clear), so the
> parts inside it may be visible. When I save this assembly as a .dwf file
> and view it with Autodesk Design Review, I am able to view the clear surface
> and everything inside it perfectly. However, when I open it with Autodesk
> Freewheel, only 1/4 of the transparent cylinder shows up. Any ideas?
> Thanks.
Gyuri
Scott Sheppard - Autodesk wrote:
> Please provide the DWF as a test case.
>
>
> I am trying to upload an assembly includes a cylinder that I have extruded
> in Inventor. The surface of this cylinder is Polycarbonate (clear), so the
> parts inside it may be visible. When I save this assembly as a .dwf file
> and view it with Autodesk Design Review, I am able to view the clear surface
> and everything inside it perfectly. However, when I open it with Autodesk
> Freewheel, only 1/4 of the transparent cylinder shows up. Any ideas?
> Thanks.
