Autodesk Architectural Desktop 2007 & Prior
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic to the Top
- Bookmark
- Subscribe
- Printer Friendly Page
*Mochrie, Craig
AEC crashes ADT 3.3 and ADT 2i
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
92 Views, 11 Replies
01-31-2003 03:13 PM
I have upgraded OS to XP Pro and have installed ADT2i and then trial of
ADT3.3 Neither program will allow use of AEC objects or dwg templates, I
get a Fatal Error; Attempt to delete AecDatabaseData which still has
registered dependants.
The menu line says could not load requested module "C:\Program Files\Common
Files\Autodesk Shared\AecBase20.dbx".
I cannot open any existing drawings that contain Aec Objects.
Please assist.
Craig.
ADT3.3 Neither program will allow use of AEC objects or dwg templates, I
get a Fatal Error; Attempt to delete AecDatabaseData which still has
registered dependants.
The menu line says could not load requested module "C:\Program Files\Common
Files\Autodesk Shared\AecBase20.dbx".
I cannot open any existing drawings that contain Aec Objects.
Please assist.
Craig.
*Medina, Alfredo
Re: AEC crashes ADT 3.3 and ADT 2i
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
01-31-2003 09:07 PM in reply to:
*Mochrie, Craig
Crag,
Run a reinstallation of ADT. Select the option named as "Repair AEC loading
mechanism". That might fix the problem.
Alfredo Medina
"Craig Mochrie" wrote in message
news:2283A08792DDC7221F760C0F8C2E2B51@in.WebX.maYI
>(...)>
> The menu line says could not load requested module "C:\Program Files\Common
> Files\Autodesk Shared\AecBase20.dbx".
>
> I cannot open any existing drawings that contain Aec Objects.
(...)
Run a reinstallation of ADT. Select the option named as "Repair AEC loading
mechanism". That might fix the problem.
Alfredo Medina
"Craig Mochrie"
news:2283A08792DDC7221F760C0F8C2E2B51@in.WebX.maYI
>(...)>
> The menu line says could not load requested module "C:\Program Files\Common
> Files\Autodesk Shared\AecBase20.dbx".
>
> I cannot open any existing drawings that contain Aec Objects.
(...)
*Bromell, Paul
Re: AEC crashes ADT 3.3 and ADT 2i
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-01-2003 01:57 AM in reply to:
*Mochrie, Craig
Someone please correct me if I'm wrong because I don't know for sure but I
don't believe that those 2 programs can co-exist on the same drive/machine.
A search through these newsgroups should yield an answer to that.
--
Paul Bromell - Metalstuff
"Craig Mochrie" wrote in message
news:2283A08792DDC7221F760C0F8C2E2B51@in.WebX.maYI
> I have upgraded OS to XP Pro and have installed ADT2i and then trial of
> ADT3.3 Neither program will allow use of AEC objects or dwg templates, I
> get a Fatal Error; Attempt to delete AecDatabaseData which still has
> registered dependants.
>
> The menu line says could not load requested module "C:\Program
Files\Common
> Files\Autodesk Shared\AecBase20.dbx".
>
> I cannot open any existing drawings that contain Aec Objects.
>
> Please assist.
>
> Craig.
>
>
don't believe that those 2 programs can co-exist on the same drive/machine.
A search through these newsgroups should yield an answer to that.
--
Paul Bromell - Metalstuff
"Craig Mochrie"
news:2283A08792DDC7221F760C0F8C2E2B51@in.WebX.maYI
> I have upgraded OS to XP Pro and have installed ADT2i and then trial of
> ADT3.3 Neither program will allow use of AEC objects or dwg templates, I
> get a Fatal Error; Attempt to delete AecDatabaseData which still has
> registered dependants.
>
> The menu line says could not load requested module "C:\Program
Files\Common
> Files\Autodesk Shared\AecBase20.dbx".
>
> I cannot open any existing drawings that contain Aec Objects.
>
> Please assist.
>
> Craig.
>
>
*Mochrie, Craig
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-01-2003 10:49 AM in reply to:
*Mochrie, Craig
Alfred,
Thank you for the suggestion. I reinstalled ADT2i and can now use the
metric aec template, however no AEC applications are loaded. I could not
find the Repair AEC loading mechanism option, is this in ADT 3.3 only? If I
load AecData.dbx by manually looking for the file, same error about
dependants comes up and it crashes again. Also on loading I get a error
that the shortcut has a bad profile in the ADT.arg and that the one in the
registry will be substituted.
Craig.
Thank you for the suggestion. I reinstalled ADT2i and can now use the
metric aec template, however no AEC applications are loaded. I could not
find the Repair AEC loading mechanism option, is this in ADT 3.3 only? If I
load AecData.dbx by manually looking for the file, same error about
dependants comes up and it crashes again. Also on loading I get a error
that the shortcut has a bad profile in the ADT.arg and that the one in the
registry will be substituted.
Craig.
*Medina, Alfredo
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 12:33 AM in reply to:
*Mochrie, Craig
Craig,
Yes, that option is in the ADT3.3 installation CD. Also, I think the problem might be
caused for trying to have ADT2i and ADT3.3 installed in the same machine. Why don't
you just leave one version?
Alfredo Medina
"Craig Mochrie" wrote in message
news:FD3F01D444E2D2A1EFA239B409245581@in.WebX.maYI
> Alfred,
>
> Thank you for the suggestion. I reinstalled ADT2i and can now use the
> metric aec template, however no AEC applications are loaded. I could not
> find the Repair AEC loading mechanism option, is this in ADT 3.3 only?(...)
Yes, that option is in the ADT3.3 installation CD. Also, I think the problem might be
caused for trying to have ADT2i and ADT3.3 installed in the same machine. Why don't
you just leave one version?
Alfredo Medina
"Craig Mochrie"
news:FD3F01D444E2D2A1EFA239B409245581@in.WebX.maYI
> Alfred,
>
> Thank you for the suggestion. I reinstalled ADT2i and can now use the
> metric aec template, however no AEC applications are loaded. I could not
> find the Repair AEC loading mechanism option, is this in ADT 3.3 only?(...)
*Mochrie, Craig
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 07:34 AM in reply to:
*Mochrie, Craig
Alfredo,
I have only ADT2i on the machine at present. I would like to be able to go
back to a fully functioning 2i before I load 3.3 again. I am reluctant to
try 3.3 again until I,( with the assistance of people like yourself), have
repaired the problem. I would like to know what caused the error in the
first place.
I have only ADT2i on the machine at present. I would like to be able to go
back to a fully functioning 2i before I load 3.3 again. I am reluctant to
try 3.3 again until I,( with the assistance of people like yourself), have
repaired the problem. I would like to know what caused the error in the
first place.
*Medina, Alfredo
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 10:51 AM in reply to:
*Mochrie, Craig
Craig,
The problem might have been caused when you tried to have the two programs
simultaneously. I understand that these two versions cannot coexist in the same
system.
Alfredo
"Craig Mochrie" wrote in message
news:C453FE78FFAEE9F172B6568363C27713@in.WebX.maYI
> Alfredo,
>
> I have only ADT2i on the machine at present. I would like to be able to go
> back to a fully functioning 2i before I load 3.3 again. I am reluctant to
> try 3.3 again until I,( with the assistance of people like yourself), have
> repaired the problem. I would like to know what caused the error in the
> first place.
>
>
The problem might have been caused when you tried to have the two programs
simultaneously. I understand that these two versions cannot coexist in the same
system.
Alfredo
"Craig Mochrie"
news:C453FE78FFAEE9F172B6568363C27713@in.WebX.maYI
> Alfredo,
>
> I have only ADT2i on the machine at present. I would like to be able to go
> back to a fully functioning 2i before I load 3.3 again. I am reluctant to
> try 3.3 again until I,( with the assistance of people like yourself), have
> repaired the problem. I would like to know what caused the error in the
> first place.
>
>
*Mochrie, Craig
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 01:30 PM in reply to:
*Mochrie, Craig
Alfredo,
I think you are right, I should not have installed 3.3 with 2, however 3.3
and 2i are supposed to be able to coexist on same box.
I still haven't been able to "clean" my machine to ensure a clean install as
the problems persist after removal and re-installation.
Do you know of a sure fire way to rid an XP Pro box of ADT (without
formatting and reloading the OS I mean!)
Craig
I think you are right, I should not have installed 3.3 with 2, however 3.3
and 2i are supposed to be able to coexist on same box.
I still haven't been able to "clean" my machine to ensure a clean install as
the problems persist after removal and re-installation.
Do you know of a sure fire way to rid an XP Pro box of ADT (without
formatting and reloading the OS I mean!)
Craig
*Medina, Alfredo
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 10:08 PM in reply to:
*Mochrie, Craig
Craig,
After the uninstallations of both programs, make sure that you remove the
folders as well. Then, re-start the machine, and install ADT3.3 again. That
should work.
Alfredo Medina
"Craig Mochrie" wrote in message
news:9E4AC1D020BDEF8A9667B5F435FB604F@in.WebX.maYI
> Alfredo,
(...)
> Do you know of a sure fire way to rid an XP Pro box of ADT (without
> formatting and reloading the OS I mean!)
After the uninstallations of both programs, make sure that you remove the
folders as well. Then, re-start the machine, and install ADT3.3 again. That
should work.
Alfredo Medina
"Craig Mochrie"
news:9E4AC1D020BDEF8A9667B5F435FB604F@in.WebX.maYI
> Alfredo,
(...)
> Do you know of a sure fire way to rid an XP Pro box of ADT (without
> formatting and reloading the OS I mean!)
*Services, Tony - Autodesk Professional
Re:
Options
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Email to a Friend
- Report Inappropriate Content
02-02-2003 10:28 PM in reply to:
*Mochrie, Craig
Arch Desktop 2i and 3.3 can co-exist on the same
system. The following is the install order that must be followed to allow
these products to function on the same system:
1. Install Arch Desktop
2i.
system. The following is the install order that must be followed to allow
these products to function on the same system:
1. Install Arch Desktop
2i.
2. Install service pack 1 for Arch
Desktop 2i.
Desktop 2i.
3. Install Arch Desktop 3.3.
And that should about cover it. Since you
have had problems with your previous installations, I would recommend
uninstalling and reinstalling all of your Autodesk software according to the
following solution:
href="http://support.autodesk.com/getdoc.asp?id=TS
have had problems with your previous installations, I would recommend
uninstalling and reinstalling all of your Autodesk software according to the
following solution:
href="http://support.autodesk.com/getdoc.asp?id=TS
Tony
Building Industry Division
Americas
Support Delivery
Autodesk Professional Services
Building Industry Division
Americas
Support Delivery
Autodesk Professional Services
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"Alfredo Medina" <Craig,
href="mailto:amedina@thepriscogroup.com">amedina@thepriscogroup.com>
wrote in message
href="news:4D85067FC3495C7854975D4AA8EC33EE@in.WebX.maYIadrTaRb">news:4D85067FC3495C7854975D4AA8E......
After
the uninstallations of both programs, make sure that you remove the
folders
as well. Then, re-start the machine, and install ADT3.3 again. That
should
work.
Alfredo Medina
"Craig Mochrie" <
href="mailto:craig@selectshopfitting.com.au">craig@selectshopfitting.com.au>
wrote in message
href="news:9E4AC1D020BDEF8A9667B5F435FB604F@in.WebX.maYIadrTaRb">news:9E4AC1D020BDEF8A9667B5F435F......
>
Alfredo,
(...)
> Do you know of a sure fire way to rid an XP Pro box
of ADT (without
> formatting and reloading the OS I
mean!)
