AutoCAD Structural Detailing General DIscussion

AutoCAD Structural Detailing General DIscussion

Reply
Contributor
RedNova
Posts: 17
Registered: ‎01-30-2013
Message 1 of 6 (2,825 Views)

Holes which are not perpendicular to profile face are not recognized in drawings

2825 Views, 5 Replies
02-28-2013 04:59 AM

Hi.

Sometimes, it is necessary to create a bolted connection between profiles which are not absolutely parallel.

In this case you have to create a "not perpendicular to face" hole at least on one of profiles.

The issue is that when you try to create drawing for the profile, these holes will not be recognized and placed on the drawing. In fact ASD will even not notice that some mechanical cutting exists and if you use automatic part shortening then hole can be just hidden. Whatever I try I cannot make this hole recognized. And put hole mark on it. See the image below:

Hole not perpendicular is not recognized.jpg

Valued Contributor
tedmail
Posts: 86
Registered: ‎04-26-2011
Message 2 of 6 (2,754 Views)

Re: Holes which are not perpendicular to profile face are not recognized in draw

03-05-2013 11:21 AM in reply to: RedNova

when creating the automatic drawings settings, have you checked the checkbox for "holes" and all?  There's quite a few uptions about holes there, depending on single part, group, etc...  But it looks like you have htem showing up properly, just not included in the dimensions, which leeds me to beleive the checkbox theory...

 

Hope that helps!

Contributor
RedNova
Posts: 17
Registered: ‎01-30-2013
Message 3 of 6 (2,722 Views)

Re: Holes which are not perpendicular to profile face are not recognized in draw

03-09-2013 09:19 AM in reply to: tedmail

I think you meant "holes in view" checkbox in dimensioning style settings. Well, here I put all possible ones and nothing helps. The point is that all usual holes and even hidden holes are displayed in drawings correctly. But whenever hole is not perpendicular to the surface (starting about on 3 degree difference) it will not be understood during drawing generating. Try yourselves. To display this kind of hole in drawing I had to recheck all my model and add a usual hole above. So I suppose this is one of bugs we meet in ASD.

 

 

Valued Contributor
tedmail
Posts: 86
Registered: ‎04-26-2011
Message 4 of 6 (2,677 Views)

Re: Holes which are not perpendicular to profile face are not recognized in draw

03-11-2013 08:09 PM in reply to: RedNova

I don't know that I would call it a bug, but maybe they need an option for an "off angle" hole.

Valued Contributor
tony
Posts: 62
Registered: ‎02-08-2011
Message 5 of 6 (2,634 Views)

Re: Holes which are not perpendicular to profile face are not recognized in draw

03-15-2013 03:19 PM in reply to: RedNova

Give this a try.

Use the bolt to generate the hole in the top angle only, then change the UCS to suit the twisted angle and then generate a single hole in tis angle so it lines up with the bolt

 

Regards

Contributor
RedNova
Posts: 17
Registered: ‎01-30-2013
Message 6 of 6 (2,569 Views)

Re: Holes which are not perpendicular to profile face are not recognized in draw

03-22-2013 11:03 PM in reply to: tony

Finally I did it following way:

Created "not perpendicular" bolted connection and then added one more hole (hole 2) above bolt's hole (hole 1) in profile's UCS. I had to create hole 2 somewhere nearby and move to same position with hole 1 because ASD is not placing new it above hole 1 if you try to do it in one step.

I made a project of telecom tower and I had a lot of "not perpendicular" connections, so I had to repeat this steps for all of them to be sure that holes will not be lost on detailed drawing :smileysad:.

 

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD Structural Detailing Category!

The AutoCAD Structural Detailing forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.

Ask the Community