AutoCAD Structural Detailing General

Reply
Active Member
Posts: 8
Registered: ‎06-28-2012
Message 1 of 6 (450 Views)

ASD Dimensioning and call outs (style)

450 Views, 5 Replies
10-12-2012 03:34 PM

Is it possible to change the ASD generated call out on prints form:

2 Ø ½” to 2 - ½” Ø or just get the hole symbol Ø at the end of the call out

Product Support
Jakub.Brozonowicz
Posts: 314
Registered: ‎12-13-2010
Message 2 of 6 (409 Views)

Re: ASD Dimensioning and call outs (style)

10-15-2012 02:18 AM in reply to: Rick

Would you like to check attached movie?

Is this what solves your problem after change in default style?

 

---------------------------------------------
If this post answer your question please click "Accept as Solution". It will help everyone to find answer more quickly!



Jakub Brożonowicz
Active Member
Posts: 8
Registered: ‎06-28-2012
Message 3 of 6 (395 Views)

Re: ASD Dimensioning and call outs (style)

10-15-2012 09:14 AM in reply to: Jakub.Brozonowicz
I could not open the file Using windows 7 and windows explorer plus I down loaded the adobe flash. Could not get it to run. Thanks you for the reply would love to find the answer. [- Description: SS_logo_1x1] Rick Thompson Superior Steel and Ironworkers LLC 21229 84th Avenue South Kent, WA 98027 425-677-8100 Office | 866-588-4766 Fax | 206-450-0794 Cell rickthompson@superiorsteel.comThis message contains confidential information intended only for use by the intended recipient(s). If you are not an intended recipient any distribution, duplication or use of this message or any attachments is not permitted. If you received this message in error please immediately advise the sender by reply e-mail and delete the original message. Thank you
Product Support
Jakub.Brozonowicz
Posts: 314
Registered: ‎12-13-2010
Message 4 of 6 (376 Views)

Re: ASD Dimensioning and call outs (style)

10-16-2012 12:29 AM in reply to: Rick

Please find the video here .



Jakub Brożonowicz
Active Member
Posts: 8
Registered: ‎06-28-2012
Message 5 of 6 (364 Views)

Re: ASD Dimensioning and call outs (style)

10-16-2012 11:22 AM in reply to: Jakub.Brozonowicz
The video on modifying the style is of help. And thank you but what I would like is to change the style so it is a standard. so they will always look that way. Change it in ASD [- Description: SS_logo_1x1] Rick Thompson
Product Support
Jakub.Brozonowicz
Posts: 314
Registered: ‎12-13-2010
Message 6 of 6 (339 Views)

Re: ASD Dimensioning and call outs (style)

10-18-2012 07:39 AM in reply to: Rick

Request for change was sent.



Jakub Brożonowicz

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you interested in helping shape the Autodesk Community?
We’re looking at a few different ways to improve the “All Forums” landing page and need your feedback! If interested, please take a few minutes to fill out the following Usability Study. Thank you for your time!

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD Structural Detailing Category!

The AutoCAD Structural Detailing forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.

Ask the Community