AutoCAD Land Desktop

Reply
Member
Jesse-Designer
Posts: 3
Registered: ‎06-09-2004
Message 1 of 10 (2,081 Views)

Paper Space Polylines Display

2081 Views, 9 Replies
06-09-2004 09:10 AM
Hi. I'm looking for a setting that controls the display on paper space for polylines. When I go from model space to paper space the polyline widths are shown as hollow, not filled. I have tried numerous settings but no luck.

The polylines show up in model space but not in paper space.

thanks,

jesse
*Joe bouza
Message 2 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 09:12 AM in reply to: Jesse-Designer
Hollow? Maybe what you want is lintype generation = enabled Joe "Jesse-Designer" wrote in message news:3226828.1086797445233.JavaMail.jive@jiveforum1.autodesk.com... > Hi. I'm looking for a setting that controls the display on paper space for polylines. When I go from model space to paper space the polyline widths are shown as hollow, not filled. I have tried numerous settings but no luck. > > The polylines show up in model space but not in paper space. > > thanks, > > jesse
*Karl Fuls
Message 3 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 09:40 AM in reply to: Jesse-Designer
Fillmode Type: Integer Saved in: Drawing Initial value: 1 Specifies whether hatches (including solid fills and gradient fills), two-dimensional solids, and wide polylines are filled in. 0 Objects are not filled 1 Objects are filled If the plines have a linetype, make sure PSLTSCALE is set to 0. -- Karl Fuls PLS Autocad AEC Training and Consulting Autodesk Discussion Group Facilitator Joe bouza wrote: > Hollow? > > Maybe what you want is lintype generation = enabled > > Joe > "Jesse-Designer" wrote in message > news:3226828.1086797445233.JavaMail.jive@jiveforum1.autodesk.com... > >>Hi. I'm looking for a setting that controls the display on paper space > > for polylines. When I go from model space to paper space the polyline > widths are shown as hollow, not filled. I have tried numerous settings but > no luck. > >>The polylines show up in model space but not in paper space. >> >>thanks, >> >>jesse > > >
*Joe bouza
Message 4 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 09:54 AM in reply to: Jesse-Designer
Thanks Karl Joe "Karl Fuls" wrote in message news:40c73d69$1_2@newsprd01... > Fillmode > > Type: Integer > Saved in: Drawing > Initial value: 1 > > Specifies whether hatches (including solid fills and gradient fills), > two-dimensional solids, and wide polylines are filled in. > > > 0 Objects are not filled > > 1 Objects are filled > > If the plines have a linetype, make sure PSLTSCALE is set to 0. > > -- > Karl Fuls PLS > Autocad AEC Training and Consulting > Autodesk Discussion Group Facilitator > > Joe bouza wrote: > > > Hollow? > > > > Maybe what you want is lintype generation = enabled > > > > Joe > > "Jesse-Designer" wrote in message > > news:3226828.1086797445233.JavaMail.jive@jiveforum1.autodesk.com... > > > >>Hi. I'm looking for a setting that controls the display on paper space > > > > for polylines. When I go from model space to paper space the polyline > > widths are shown as hollow, not filled. I have tried numerous settings but > > no luck. > > > >>The polylines show up in model space but not in paper space. > >> > >>thanks, > >> > >>jesse > > > > > > >
*Joe bouza
Message 5 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 09:57 AM in reply to: Jesse-Designer
Hi Karl, no chance that can be set by entity, would there? Joe "Karl Fuls" wrote in message news:40c73d69$1_2@newsprd01... > Fillmode > > Type: Integer > Saved in: Drawing > Initial value: 1 > > Specifies whether hatches (including solid fills and gradient fills), > two-dimensional solids, and wide polylines are filled in. > > > 0 Objects are not filled > > 1 Objects are filled > > If the plines have a linetype, make sure PSLTSCALE is set to 0. > > -- > Karl Fuls PLS > Autocad AEC Training and Consulting > Autodesk Discussion Group Facilitator > > Joe bouza wrote: > > > Hollow? > > > > Maybe what you want is lintype generation = enabled > > > > Joe > > "Jesse-Designer" wrote in message > > news:3226828.1086797445233.JavaMail.jive@jiveforum1.autodesk.com... > > > >>Hi. I'm looking for a setting that controls the display on paper space > > > > for polylines. When I go from model space to paper space the polyline > > widths are shown as hollow, not filled. I have tried numerous settings but > > no luck. > > > >>The polylines show up in model space but not in paper space. > >> > >>thanks, > >> > >>jesse > > > > > > >
Member
Jesse-Designer
Posts: 3
Registered: ‎06-09-2004
Message 6 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 11:27 AM in reply to: Jesse-Designer
I have tried that....when in model space the polylines are shown as solid. when in paper space the polylines are shown as hollow polylines. I have changed numerous settings from lweight, lwt on status bar, options (plotting),lwdisplay. I really don't know what else it could be.

jesse
*James Wedding
Message 7 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 11:48 AM in reply to: Jesse-Designer
Is your viewport in HIDE? It could also be that your viewport is not in standard World-Plan view. That would cause the same problem. -- James Wedding, P.E. IT Manager Jones & Boyd, Inc. Dallas, TX XP/1 on P4-3.4/1G LDT2004&5+C3D Troll :a slang term for a person who posts messages without contributory content, simply intended to incite conflict. http://wikipedia.com
Member
Jesse-Designer
Posts: 3
Registered: ‎06-09-2004
Message 8 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 12:03 PM in reply to: Jesse-Designer
James,

yes i have already checked for that. I finally just started over and by doing so, it fixed the problem. It was very strange and in only 5 of my drawings had the same problem. How is Luke Peters doing? He is a friend of mine.

Thanks for your input.

Jesse
*James Wedding
Message 9 of 10 (2,081 Views)

Re: Paper Space Polylines Display

06-09-2004 12:11 PM in reply to: Jesse-Designer
He's doing great. Under the gun and performing admirably. -- James Wedding, P.E. IT Manager Jones & Boyd, Inc. Dallas, TX XP/1 on P4-3.4/1G LDT2004&5+C3D Troll :a slang term for a person who posts messages without contributory content, simply intended to incite conflict. http://wikipedia.com
New Member
papa2ten
Posts: 1
Registered: ‎04-06-2011
Message 10 of 10 (1,865 Views)

Re: Paper Space Polylines Display

04-06-2011 08:02 AM in reply to: Jesse-Designer

Solution for ACAD LT 2009:
delete and re-layout viewport in paperspace.

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community