AutoCAD Electrical General

Reply
Active Contributor
elprim
Posts: 28
Registered: ‎07-31-2010
Message 1 of 8 (349 Views)
Accepted Solution

ACE2012 Link components & reverse component

349 Views, 7 Replies
09-11-2012 05:17 AM

Hi

 

What is the right way to unlink component

 

I have reversed the component and then I wasn't able to connect wire,

 the connection was made over component, what I make wrong

 

Thank for help, Vito

Kind regards, Vito
*Expert Elite*
testsubject
Posts: 1,072
Registered: ‎03-09-2004
Message 2 of 8 (346 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 05:58 AM in reply to: elprim

How did you reverse the component? If you simply mirrored it, then ACE will not work properly. You have to use the "Reverse/Flip Component"Command. One way of finding it is to hover over the component and then Right Mouse Click. This command is located near the bottom.

 

You can use "Trim WIre" to disconnect a component from the wiring.

Bob Hanrahan
Ace User since 1998
Active Contributor
elprim
Posts: 28
Registered: ‎07-31-2010
Message 3 of 8 (343 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 06:30 AM in reply to: testsubject

Hi, I used "Reverse/Flip Component" and result is in attachment

 

block is VSS21 and VSS113

 

 

Thanks, Vito

 

 

Kind regards, Vito
*Expert Elite*
testsubject
Posts: 1,072
Registered: ‎03-09-2004
Message 4 of 8 (339 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 06:36 AM in reply to: elprim

Can you send the .dwg file? I cannot see how the symbol is created done from a jpeg...

Bob Hanrahan
Ace User since 1998
*Expert Elite*
testsubject
Posts: 1,072
Registered: ‎03-09-2004
Message 5 of 8 (338 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 06:37 AM in reply to: testsubject

Also what library are you using? IEC2, IEC4, JIC1, JIC125, etc? They all use the same file names but the drawings are different.

Bob Hanrahan
Ace User since 1998
Active Contributor
elprim
Posts: 28
Registered: ‎07-31-2010
Message 6 of 8 (336 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 06:45 AM in reply to: testsubject

Hi,

 

I use IEC60617 and ACE 2013

Kind regards, Vito
*Expert Elite*
testsubject
Posts: 1,072
Registered: ‎03-09-2004
Message 7 of 8 (325 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 07:43 AM in reply to: elprim

I am not sure what is wrong.

 

I had no trouble reversing any of these contacts.

 

Sorry that I could be of more help.

Bob Hanrahan
Ace User since 1998
*Expert Elite*
Icemanau
Posts: 911
Registered: ‎06-01-2010
Message 8 of 8 (316 Views)

Re: ACE2012 Link components & reverse component

09-11-2012 03:25 PM in reply to: testsubject

When you reversed the contacts, did you check the box to only reverse the graphics?

 

I've had similar problems in the past when reversing a component and found that if I didn't check that box, the attributes would also be moved but the wire direction wouldn't change.

 

Regards Brad

Icemanau (NNTP handle: Brad Coleman)


You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Manufacturing Community
The Manufacturing Community provides additional access to tips, tutorials, blogs and networking with peers.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

New AutoCAD Electrical Category!

The AutoCAD Electrical forum has moved into it's very own category page, and can no longer be found within the Additional Product Forums.

Ask the Community