New Member
Posts: 2
Registered: ‎08-09-2006
Message 1 of 9 (284 Views)

# degree of curvature

284 Views, 8 Replies
08-09-2006 06:58 AM
Has anyone figured out to get the degree of curvature (DOC) for a curve in an alignment to be reported for Civil 3D 2007 like was reported in the 2006 version?
*Connie B
Message 2 of 9 (284 Views)

# Re: degree of curvature

08-09-2006 11:10 AM in reply to: thorius
Do you need it for highway or railroad curves?

wrote in message news:5263131@discussion.autodesk.com...
Has anyone figured out to get the degree of curvature (DOC) for a curve in
an alignment to be reported for Civil 3D 2007 like was reported in the 2006
version?
New Member
Posts: 2
Registered: ‎08-09-2006
Message 3 of 9 (284 Views)

# Re: degree of curvature

08-09-2006 11:12 AM in reply to: thorius
I need it for highway curves.
Employee
Posts: 31
Registered: ‎11-02-2005
Message 4 of 9 (284 Views)

# Re: degree of curvature

08-09-2006 11:59 AM in reply to: thorius
You can add an expression to the curve label... see the attached gif file.

Karen Dowling
Autodesk ISD Test Development
Member
Posts: 4
Registered: ‎10-26-2006
Message 5 of 9 (284 Views)

# Re: degree of curvature

10-31-2006 10:40 AM in reply to: thorius
How does one go about getting degree of curvature (D) to display in a label for a PI in C3D 2006?
Contributor
Posts: 15
Registered: ‎01-04-2007
Message 6 of 9 (284 Views)

# Re: degree of curvature

11-05-2008 07:57 AM in reply to: thorius
Ok, but how do I get the radius into this calculation?

Thank you,
Tom
*wfb
Message 7 of 9 (284 Views)

# Re: degree of curvature

11-05-2008 09:39 AM in reply to: thorius

One would assume it will get the radius from the
selected curve.

Bill

style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
Ok,
but how do I get the radius into this calculation? Thank you,
Tom
Contributor
Posts: 15
Registered: ‎01-04-2007
Message 8 of 9 (284 Views)

# Re: degree of curvature

11-05-2008 10:08 AM in reply to: thorius
Radius was not a choice in the expression inset property list. Turns out that I was in the general label styles section, not the Alignment>label sytles>curve section. So, there are different choices available based on what area you are in.
Mentor
Posts: 1,244
Registered: ‎04-09-2010
Message 9 of 9 (50 Views)

# Re: degree of curvature

08-03-2013 10:45 AM in reply to: Karen Dowling

How to set and label the “degree of curvature”?

As the radius of the circular alignment is calculated from the “degree of curvature” (attached) then I couldn’t figure out how to change the default value or to label it (degree of curvature)

Thank you

Best

Jamal

----------------------------------------------------------
Jamal NUMAN, GIS and Civil Engineer, MSc
e-mail: JamaL9722060@yahoo.com
P.O.Box: 731, Ramallah, West Bank, Palestine.
----------------------------------------------------------
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.

Recently Solved