Contributor
Posts: 14
Registered: ‎06-06-2012
Message 1 of 8 (492 Views)

# Z distance in inches not feet

492 Views, 7 Replies
12-11-2012 11:12 AM

I have a very simple surface. All of the elevations defining it, are set in feet. When I click on the surface it tells me my max and min elevations are in feet matching the points that I have defining the surface.

Here is the kicker, when I run a distance it is measuring the Z distance in inches and not feet. As you can see by the attached image the distance is 95' but the elevation change is 1 3/8".  The actual points defining the surface are 1.28' difference. If I were to do a spot elevation on the surface, it would give me the correct elevation in feet.

Can anyone tell me whats going on? I am guessing that this is some sort of variable that I have missed, but damned if I can find it.

*Expert Elite*
Posts: 2,519
Registered: ‎05-21-2008
Message 2 of 8 (483 Views)

# Re: Z distance in inches not feet

12-11-2012 11:17 AM in reply to: ajfernandes

Try setting your units to decimal feet rather than feet & inches.

Credit where credit is due! Give kudos or accept as solution whenever you can.

Contributor
Posts: 14
Registered: ‎06-06-2012
Message 3 of 8 (478 Views)

# Re: Z distance in inches not feet

12-11-2012 11:27 AM in reply to: troma

Unfortunately that didn't work. It just changed my measurements to inches instead. But kept the z measurement the same.

Any other ideas?

*Expert Elite*
Posts: 2,519
Registered: ‎05-21-2008
Message 4 of 8 (475 Views)

# Re: Z distance in inches not feet

12-11-2012 11:31 AM in reply to: ajfernandes

Can you repeat the screen shot with the new units setting?

Credit where credit is due! Give kudos or accept as solution whenever you can.

Contributor
Posts: 14
Registered: ‎06-06-2012
Message 5 of 8 (471 Views)

# Re: Z distance in inches not feet

12-11-2012 11:36 AM in reply to: troma

Here is a screen shot of the units set to decimal instead of architectural.

*Expert Elite*
Posts: 2,519
Registered: ‎05-21-2008
Message 6 of 8 (465 Views)

# Re: Z distance in inches not feet

12-11-2012 11:42 AM in reply to: ajfernandes

I've always worked in metric so I don't really know how the imperial settings work in C3D, but I know that it is always meant to be feet, not inches.  It looks like all your distances are off by a factor of 12, so you may have started up wrong from the begining, I don't know.

Could really do with someone else jumping in here to help, but unfortunatly when the topic is marked as solved others may not look into it.

Credit where credit is due! Give kudos or accept as solution whenever you can.

Contributor
Posts: 14
Registered: ‎06-06-2012
Message 7 of 8 (455 Views)

# Re: Z distance in inches not feet

12-11-2012 12:14 PM in reply to: troma

Your advice lead me to the solution. Our office has been bouncing back and forth between imperial and metric and I don't have enough experience to do this successfully.

Here is the solution. Autocad wants the drawing in Decimal Feet. I went back and scaled down the drawing by 12 so that all measurements of units were in feet. (I.E. 9.50' instead of 9'-6") Now scaling the drawing also scales the Z elevation so I had to follow the following link to redifine my points after I scaled. See this thread for how to do that (http://www.civil4d.com/2009/10/scale-your-points-keep-the-elevations/)

And now, everything makes sense again.

I'll have to reset my viewports, but small price to pay.

*Expert Elite*
Posts: 5,772
Registered: ‎05-21-2003
Message 8 of 8 (446 Views)

# Re: Z distance in inches not feet

12-11-2012 12:24 PM in reply to: ajfernandes

Make sure that you are setting your units correctly in the Drawing Settings. Go to the Toolspace and on the Settings tab - Right click on the active drawing and select, Edit Drawing Settings. Set up your units on Units and Zone tab and check 'Set AutoCAD Variables to match'.

Here is how I have mine set up for feet

### You are not logged in.

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

### Maintenance Subscription Resources

Upgrading to a 2015 product? Make sure to check these out 1st!

### Civil 3D Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for AutoCAD Civil 3D helps you achieve greater speed, accuracy, and automation from concept to manufacturing.