AutoCAD Civil 3D General

Reply
Member
DNNdrafting
Posts: 5
Registered: ‎01-28-2014
Message 1 of 5 (208 Views)
Accepted Solution

Scaling a group of points found under 'Import Events'

208 Views, 4 Replies
02-22-2014 02:58 PM

Can a group of points under Import Events (I have two events), have a scale factor applied to it AFTER they have been imported? I have received one set of survey points that are ground and the other that is grid and needs to be scaled to bring to ground. I'm new to Civil 3D, but have used MicroSurvey for a number of years.

*Expert Elite*
mathewk
Posts: 2,714
Registered: ‎07-09-2003
Message 2 of 5 (174 Views)

Re: Scaling a group of points found under 'Import Events'

02-23-2014 03:09 PM in reply to: DNNdrafting
What you could do is insert them into a blank drawing, unlock them, scale them, then remove those points from the DB and add them back into the DB from the drawing.

Be careful when scaling' the elevations will scale as well. See the link below (the images for whatever reason are gone)
http://www.civil4d.com/2007/06/spare-change-for-a-scale-change/
Matt Kolberg
Cansel - Autodesk Division
http://www.cansel.ca/
Member
DNNdrafting
Posts: 5
Registered: ‎01-28-2014
Message 3 of 5 (161 Views)

Re: Scaling a group of points found under 'Import Events'

02-24-2014 07:38 AM in reply to: DNNdrafting

Thanks for your help - AGAIN - Matt! Always good suggestions. Would this issue be adressed in C3D 2015? I think, after reading more of the feedback, that 2 dimensional scaling (Z= x1.00) applied to point groups would be a welcome addition.

*Expert Elite*
mathewk
Posts: 2,714
Registered: ‎07-09-2003
Message 4 of 5 (141 Views)

Re: Scaling a group of points found under 'Import Events'

02-24-2014 11:57 AM in reply to: DNNdrafting

It's possible, but I doubt that this behavior will change for 2015, just my gut feeling.  We won't know until it's released...whenever that is.

Matt Kolberg
Cansel - Autodesk Division
http://www.cansel.ca/
Distinguished Contributor
cbaildon001
Posts: 151
Registered: ‎06-28-2008
Message 5 of 5 (108 Views)

Re: Scaling a group of points found under 'Import Events'

02-26-2014 03:02 PM in reply to: mathewk

In your survey database settings you can turn a Scale factor correction. This applies a scale factor to all observed distances upon import of a FBK file.

 

So if you are dealing with and observation FBK file, work out the scale factor, enter it in the FBK file SCALE FACTOR XXXX, then reimport the FBK.

 

I don't think it scales any NEZ control points but if you have the correct values for your starting points in the FBK you should be fine.

Caleb Baildon
Surveyor
Opus International Consultants Ltd
Greymouth, New Zealand
Civil3D 2015 - Windows7 64bit

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Civil 3D Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for AutoCAD Civil 3D helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Civil 3D

Twitter

Facebook

Blogs