AutoCAD 2013/2014/2015

Reply
Contributor
Posts: 15
Registered: ‎09-03-2012
Message 1 of 6 (1,263 Views)

Unhandled Access Violation reading 0xffffffff exception at e14572a7h

1263 Views, 5 Replies
02-14-2013 12:06 AM

Hi Everyone,

 

We're trying to elete an object with a constrain on it in ourdrawing. Problem is, when we try to either delete the object or remove the constraint on it, our AutoCAD 2013 crashes with the error in the subject. Additional detail is that the file was created in a lower version, I'm hazy on it but I think it was created on AutoCAD 2011. 

 

Has anyone else encountered this problem? Thanks. :smileyhappy:

*Expert Elite*
rkmcswain
Posts: 2,586
Registered: ‎11-13-2006
Message 2 of 6 (1,247 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 04:59 AM in reply to: ronane

Is this a crash you can repeat in any new empty drawing, or does this only happen in a particular drawing?

Contributor
Posts: 15
Registered: ‎09-03-2012
Message 3 of 6 (1,238 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 05:18 PM in reply to: rkmcswain

Hi rkmcswain,

 

The error is only for a specific drawing.

*Expert Elite*
braudpat
Posts: 1,589
Registered: ‎12-15-2006
Message 4 of 6 (1,228 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 11:36 PM in reply to: ronane

 

Hello

 

Could you open your DWG in RECOVERY Mode and then Re-Save it ...

 

Have you yet the same problem ?

 

Bye, Patrice

 

Bye, Pat

Contributor
Posts: 15
Registered: ‎09-03-2012
Message 5 of 6 (1,224 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 11:53 PM in reply to: braudpat

Hi Patrice,

 

Thanks for the reply. We can't open it in RECOVER, it just crashes. It just says  "problems were were detected. recommend that you save your work and restart program."

*Expert Elite*
braudpat
Posts: 1,589
Registered: ‎12-15-2006
Message 6 of 6 (1,215 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-15-2013 02:48 AM in reply to: ronane

 

Hello

 

Aie, Aie, your DWG seems very damaged !

 

An other idea : from a blank DWG with correct Units

Try to insert it at 0,0 - Rotation = 0 - Scale = 1 - In exploded mode

 

If OK, please try immediateley an AUDIT

 

Good Luck, Bye, Patrice

 

 

Bye, Pat

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community




Connect with AutoCAD

Twitter

Facebook

Blogs

Pinterest

Youtube