AutoCAD 2013/2014/2015

Reply
Contributor
ronane
Posts: 15
Registered: ‎09-03-2012
Message 1 of 6 (1,549 Views)

Unhandled Access Violation reading 0xffffffff exception at e14572a7h

1549 Views, 5 Replies
02-14-2013 12:06 AM

Hi Everyone,

 

We're trying to elete an object with a constrain on it in ourdrawing. Problem is, when we try to either delete the object or remove the constraint on it, our AutoCAD 2013 crashes with the error in the subject. Additional detail is that the file was created in a lower version, I'm hazy on it but I think it was created on AutoCAD 2011. 

 

Has anyone else encountered this problem? Thanks. :smileyhappy:

*Expert Elite*
rkmcswain
Posts: 3,186
Registered: ‎11-13-2006
Message 2 of 6 (1,533 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 04:59 AM in reply to: ronane

Is this a crash you can repeat in any new empty drawing, or does this only happen in a particular drawing?

Contributor
ronane
Posts: 15
Registered: ‎09-03-2012
Message 3 of 6 (1,524 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 05:18 PM in reply to: rkmcswain

Hi rkmcswain,

 

The error is only for a specific drawing.

*Expert Elite*
braudpat
Posts: 1,890
Registered: ‎12-15-2006
Message 4 of 6 (1,514 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 11:36 PM in reply to: ronane

 

Hello

 

Could you open your DWG in RECOVERY Mode and then Re-Save it ...

 

Have you yet the same problem ?

 

Bye, Patrice

 

Bye, Pat

Contributor
ronane
Posts: 15
Registered: ‎09-03-2012
Message 5 of 6 (1,510 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-14-2013 11:53 PM in reply to: braudpat

Hi Patrice,

 

Thanks for the reply. We can't open it in RECOVER, it just crashes. It just says  "problems were were detected. recommend that you save your work and restart program."

*Expert Elite*
braudpat
Posts: 1,890
Registered: ‎12-15-2006
Message 6 of 6 (1,501 Views)

Re: Unhandled Access Violation reading 0xffffffff exception at e14572a7h

02-15-2013 02:48 AM in reply to: ronane

 

Hello

 

Aie, Aie, your DWG seems very damaged !

 

An other idea : from a blank DWG with correct Units

Try to insert it at 0,0 - Rotation = 0 - Scale = 1 - In exploded mode

 

If OK, please try immediateley an AUDIT

 

Good Luck, Bye, Patrice

 

 

Bye, Pat

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community




Connect with AutoCAD

Twitter

Facebook

Blogs

Pinterest

Youtube